I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi, I'm trying to using SEGGER IDE to program the nRF52840 whit both Zephyr RTOS and Nordic SDK accessible to my project. I have followed the guide on https://developer.nordicsemi...
Hi I still have problems with this board. I check it at my nRF dealer and it works. Yesterday I run it on an another PC and it works well:
But today at the same PC it...
Hello,
I am trying to implement the Peer Manager for bonding and pairing on my central device (nrf52840 Dongle) using SDK 15.3. I based my project off of the ble_app_uart_c...
Hello Nordic Semiconductor Community,
I do run mqtt_simple example successfully on my nRF9160 DK with modem firmware v1.1.1 and NCS tag v1.2.0.
Now I am connecting mqtt_simple...
Hi, I am using nrf52840 DK to create the uart ble app. The starting point is ble_app_uart example from SDK52 15.3. I changed pin configuration for uart so I can have RX and...
Hello,
I am looking into adding a whitelist to my central device to stop scanning devices I am disinterested in, however, I have a few questions and concerns about them...
Hi,
I saw the errata for bad onboard GPS antenna performance in nrf9160 DK v0.8.2 and 0.7.0
Was the problem fixed in 0.8.3, or is 0.8.3 still affected?
Thanks.
Hi,
I am using the nrf5 SDK for Mesh v4.0,
Windows 10,
4 DevKits PCA10056.
I have 2 DevKits as LPN (from the experimental_lpn example) and 2 DevKits as FNs (friend...
Hi,
I have a issue with the output regulation of REGOUT0.
I have a custom board based on the NFR52840-CKAA (revision D). I designed it in high voltage mode because I have...
Hi, I'm getting a crash when discarding an advertising packet.
Roughly what I do is:
Which crashes at advertiser_packet_discard().
GDB trace:
It looks like packet_buffer_pop...
When and by what logic Peer Manager performs garbage collection on FDS?
I have a single number stored also in FDS and I’m wondering if gc performed by Peer Manager will...
Hello,
I'm still just starting to deal with Zigbee and I have a question. I use 2 nRF52840 chips. One as a Zigbee Coordinator (CLI in SDK\examples\zigbee\experimental\cli...
Hello Sir
Sir i am try to sending the some text to nrf 52840 board,if you have any document please send it.
and how to do this process ? Sir please explain
Hi ;
If there is a ble message coming , but this time ble is getting data from sensor , what will happen ? Will it device reset ? Would you give me any idea to avoid this...
Dear all,
We have a question.
Did any body tried to make so that Bluetooth Mesh 4.2 works in PARALLEL with Bluetooth 5.
Some schedule reserved for BLE MESH 4.2 and some...
