hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
I have a nRF52840-PCA10059 dongle.
I have a PCA10040 dev boeard on which I programmed the ble_app_hrs_freertos_pca10040_s132 example after I modified HEART_RATE_MEAS_INTERVAL...
Hi,
I have some code which is based on the ble_app_gatts_c example sdk 15. I am using a Nordic NRF52840-dk pca10056 s140. Coding in Segger.
I want to each second change...
Hi,
I want to set the unused pins to low Level, however without using Software to do so, i.e. this has to be done before the chip is turned on.
How can I do that? Is...
Hello all, I have a little problem.
I`m trying to do an gateway communication using my NRF9160. The routine I`m trying to accomplish is next : -- Send message over serial...
Hi... i am getting the data through the RX,TX which is externally connected to the nRF52832 development kit , now i want to store the continous incoming data to the variable...
Hello, I am using nrf52840 board and SDK 16.0.0.
I am trying to merge this calendar example ( https://github.com/NordicPlayground/nrf5-calendar-example ) into ble_app_template...
1. I am trying to test the QSPI flash performance in nrf52840_DK ,but the QSPI init failed because of the event ready check,can i turn off the event check process?
2. I...
The recommended circuit in the v0.5 nRF5340 product spec differs a little from the nRF5340-PDK and I'm trying to understand the minimum requirements for an antenna. The spec...
Hi everyone, I am a beginner with the nRF52840 and I am looking at the example spi_pca10056 on SDK 16.0.0. What I've noticed is that at sdk_config.h file the pin configuration...
I have a question about what functionality is handled in the modem firmware vs. the application firmware.
I see from the nRF Connect SDK that the nRF9160 application communicates...
I'm using segger IDE for EVK-NINA-B1. I've downloaded nRF5_SDK_16.0.0 and trying yo run one of its example but getting error like stray '#' in program. I've attached 2 pictures...
Hi,
I'm using NRF52832 SDK15.2 to develop a smart band. Each time reconnect with iphone, the application assert in the peer manager event handler pm_evt_handler().
Any...
Hi Team,
I would like to know what does the system do after I call system off function as per below:
I have check through the oscilloscope to check how's the system...
Hi Team,
I am in the UK and trying to get an evaluation sim from Vodafone for NB-IoT. However they have set a limit of 2 IP addresses and hence I need the IP address of...
