Hi,
I've been using the nRF51 dev kit, and today it stopped mounting when I plug it in. It doesn't show up as MBED or BOOTLOADER.
I use both Mac OS X and Windows, though...
SDK_9.0.0
I was trying to implement 2 different UART connection parameters so I decide to use re-initialization.
My initial parameters included APP_UART_FLOW_CONTROL_LOW_POWER...
I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
I am encountering an issue with PERSISTENT_STORAGE enabled. Currently I have a device set up to rapidly send out messages to test the sequence number updating and block allocation...
Hi Team,
We are using nrf9160 DK and we are new to begin this, We updated modem firmware using programmer, Now we would like to test the modem firmware.
So here are...
Hello,
This is first time to design the PCB antenna for nRF52840 BLE Chip. Can i use the nRF52840 DK Board HW layout for reference or should i use the USB dongle for nRF52840...
SDK16
S132
nrf52832
SES / Windows 10
After much searching this site and the web in general I'm reaching out for support.
While in low-power mode I'm seeing a pulse...
Hello im an Android developer and we have an app that uses an older library but still works with are older products.
we currently use
implementation 'no.nordicsemi.android...
From what I read on DevZone it seems that there is a limitation in nrfutil when needed to update BL+SD+APP. NRFConnect over BLE manages the 2 separate downloads (BL+SD and...
Hello there The problem I encountered was that when getting the slave service, returning to get the service failed. I used DEBUG to check the p_ble_gattc_evt->gatt_status...
Hi,
I am using nrf Connect SDK v1.2.0 in Segger Embedded Studio 4.52 and developing on a nrf52840 development kit (pca_10056). I use the "configure nrf connect sdk project...
My goal is to establish a BLE connection between the DK and the smartphone, using NFC for the OOB pairing . I am using the nRF52 DK and the nRF5 SDK , v.16.0.0.
The intended...
Hi,
I am having issues with getting SPI up and running on my nrf52840-DK using NCS. I've tried getting support about this in another ticket but it seems like it lead to...
Hi,
We are using the nRF52840 SoC.
The following image is taken from the datasheet:
It shows a Gain block before the SAR core
a. Does the Gain block serve also...
Hi ,
I want to know if it is possible to close/open the uart connection with RTS and CTS pin in order to have a low power UART?
When RTS and CTS are high, uart is closed...
Hi,
Can any Zigbee application receive ieee radio interrupts in both TX and RX path?
What I need is:
In the case of Zigbee Tx, an advance notification of 200 μs would...
Hello, I am using nRF52 DK and softdevice s112, developing with SDK V15.2. I am exploring the fds library and have encountered some strange behavior. When I connect the nRF52...