In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Folks,
Been struggling for a couple of days with a comms issue that I assumed were at the other end of my system, but am starting to think it's at the nRF52 UART end and...
nrfutil
dfu serial -pkg ble_ app _v1 .zip
-p /dev/ttyUSB 0 - b 57600 - fc 1
When activating DFU sometimes on the last packet sent to the bootloader, I see "Read no data...
I need to know how to set up the SES debugger to continue debugging when the program jumps from application into the bootloader.
nRF52832 SDK v15.3
Using the following...
C:/Program Files/SEGGER/SEGGER Embedded Studio for ARM 4.18/gcc/arm-none-eabi/bin/ld: Output/Debug/Obj/port_cmsis_systick.o: in function `RTC1_IRQHandler':
1> .....\nRF5_SDK_for_Thread_and_Zigbee_v3...
Hi,
When I use SDK16, for example, the ble_app_hrs, the Keil will throw a error about the system_nrf52840.c.
1. For Device Family Pack version 8.27.1, it could not find...
Hello
I am contacting you because I have 2 problems:
1. I downloaded the "nRF5_SDK_for_Thread_and_Zigbee_v4.0.0_dc7186b" available at this address: www.nordicsemi.com...
Hi!
I'm using nrf52832, SDK 16 and s132. I've successfully used a ble_app_hids_keyboard example to make a Bluetooth HID peripheral device to transfer sensor data to the...
I want to use a timer to generate an event at a rate of 16kHz. So just as a test I'm setting up TIMER4 and a CC event to toggle a gpio pin. As I understand the clock source...
Hello everyone,
I set up Thread Secure OTA DFU Example by using a nrf52840 DK as DFU server and a nrf52840 Dongle as DFU client. I am using nRF5 SDK for Thread and Zigbee...
I'd be grateful for some assistance with what I may be doing wrong.
I have programmed the serial example on a device and the server example on another device.
Copied the...
Hi everyone:
I was testing the bonding with passkey entry, but it seems failed.
The slave 51822 EVK board is set with "BLE_GAP_IO_CAPS_DISPLAY_ONLY" and "MITM = 1".
...
Hello devzone! I am using translation.
I am using a DK board (PCA10056) to examine the current consumption of nRF52840. I commented out the advertising_start() of the SDK...
Hi, I'm trying to implement a mesh serial node with LPN capability, where the UART can be disabled to save power, and then re-enabled via a GPIO.
I am measuring current...
Ok -
I've been through this a few times and read the forums, but the current build system is broken. I'm trying to compile (not even load the board at this point) the ble_hts...
