Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
I am using SDK 15.3.0 and need to create a single hex file to program the initial batch of our nRF52840 based HW. Currently, I have built the bootloader project (open not...
Hi,
I'm facing some problems in the use of the Logger module when the option NRF_LOG_FILTERS_ENABLED is set in the sdk_config.h file.
I'm working with the nRF5 SDK for...
I'm trying to get LPCOMP working on Zephyr - from my research online I can see no information about this currently so I'd like to find out how to do this.
According to an...
Hi,
The documentation for the nRF52840 (section 6.20.15.9) states that RSSI has a typical accuracy of ±2 dBm. I have measured signal strength at multiple distances, and...
HI,ALL！
I use official routine development NRF51822，nRF51\nRF5_SDK_12.3.0_d7731ad\nRF5_SDK_12.3.0_d7731ad\examples\ble_central\experimental\ble_app_blinky_c\pca10028\s130...
Hi,
My problem is with generating interrupts in lsm6dso relative tilt mode.
I asked it in st community, but I didn´t get any answers.
I'm trying to implement a relative...
Hello,
I couldn't understand the predefined header files for the spi, so I'm building the spi code from scratch.
To build init_spi function, It's clearly mentioned in...
Hi,
We are currently trying to design a system using one of the nrf5 bluetooth chips. However, we are still in the process of designing a functional antenna and need to...
Hi, I am trying to implement an example that support multiple peripherals (HRS & UART). When I get a connection (from either) I get the BLE_GAP_EVT_CONNECTED. How can I differentiate...
What is exact difference between heartbeat and health models?
I know heartbeat can be used to detect node outage, but so can be health message?
So, which one should be...
When starting up the device with the nRF5 SDK 3.2.0 for mesh, even though the model and subscription list state is loaded from flash, it is stored again right afterwards....
To the kind attention of Nordic support team,
I was reading this blog https://www.ericsson.com/en/blog/2017/12/wake-up-radio--a-key-component-of-iot
May I ask if Nordic...
After Downgrade protection in the NRF9160 has been set with AT%XPRODDONE=1, switching it off with AT %XPRODDONE=0 returns ERROR. Is there a way to disable downgrade protection...
Hello DevZone,
Is there a way for hardware to update the timer capture register?
I want to create different frequencies using a single timer. Next to the timer, Bluetooth...
