Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
Dear All,
I tried to take the Capp sense example and implement it in my beacon app which was based on the beacon app example. I am using nrf52382 and sdk16 , segger version...
Hello,
I'm working on nrf52832 dfu secure bootloader example.I implemented button less example to update my firmware and it works fine.
Now i switch off the power supply...
HI , I used NRF52832 SDK15.3,examples:ble_app_ancs_c.When i testing ANCS,I deleted the pm_handler_secure_on_connection(p_ble_evt) in the ble_evt_handler function, The BLE...
Hi All,
I have one custom board based on IMX6UL on which i'm using Nordic's nrf52840 chip.
I'm using zephyr's hci_uart sample application on nrf52840 for beacon scanning...
Hi all,
Greetings of the day.
Here I am not able to flash the code which is built with IAR platform. We tried loading the IAR based blinky example project from the SDK...
Hi all,
Greetings of the day.
Here I am not able to flash the code which is built with IAR platform. We tried loading the IAR based blinky example project from the SDK...
Hi,
I am using
nRF52840
SDK 15.3.0
Keil IDE
The soft device is S140
JLinkRTTViewer for debug
How do i use a single serial port to communicate with the server...
NRF52840 development board does not have any programs when burning into bootloader and application and protocol stack and settings.hex,
Why do you need an OTA to enter the...
The questions are related to nrf9160:
How much memory space is currently used and free on the Thingy:91, nrf9160?
How much memory would take a complex timing routine...
I'm working nrf52832 , SDK V15.3.0 and S132. I have implemented whitelist in application and its working fine. I need to add one phone as master device so i need to hard coded...
Hello,
I'm using nRF52811 SoC with nRF5_SDK16.0.0 and SoftDevice v7.0.1. I'm using following code to write data into flash. This code is tested with nRF52840 in both debug...
i want to interface the adxl345 accelerometer with the nrf52840 board
i got an code from ADXL375_12C.zip
https://devzone.nordicsemi.com/cfs-file/__key/communityserver...
Hello All,
Is there an explanation why the Pin Configuration Registers are not available for viewing in the Registers view of Segger Embedded Studio?
If there is can someone...
Hello,
We have an nrf9160 dk-pca10090 board.
We want to know if there is a way to make the two processors (nrf52840 and nrf9160) communicate using uart.
Kindly...
Hi everyone
I have a question about zigbee. After reviewing the documentation, I realized that on the nrf52840 chip, you can use zigbee with a frequency of 2.4 GHz. But...
