Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi, Everyone
My development environment is PCA10040 (nRF5_SDK_14.2.0_17b948a) with IAR
The printf statement is output to the terminal (Teraterm) using the UART. However...
Hello,
Our company is considering on developing BLE products with Bluetooth 5.0 compliance in mind. I'm currently trying to get as many information as possible but I'm...
Hi,
Once applying 0V to DEC2 pin, CPU hangs up and cannot be system resetted even though we input reset signal to RESET pin.
The only way to reset is to suppress system...
I am new to Nordic and BLE mesh connectivity. I have the following assumptions & queries, Please clarify if I am wrong.
1. Is it possible to implement BLE Mesh using Thing52...
I'm trying to read data over UART as fast as possible using the double-buffering feature and EasyDMA, but even this simple example I've posted is losing data.
I've set up...
The wake on GPIO is working all the time now.
Unfortunately, I want to disable it except when needed.
Here is the scenario:
Power up, pushbutton pin senses clicks...
I am using the nrf52832 and according to the errata v1.1 the same contains a problem in the spi, according to clause 3.13 the engineering versions (QFAA-AA0, QFAA-AC0) and...
Hey..
I'm having difficulties using P1 pins for UARTE0 and/or UARTE1.
configuring the RX & TX pins like this works great:
#define RBP_UARTE0_RX_PIN_NUMBER NRF_GPIO_PIN_MAP...
Hi,
I'm using a NRF52832. I'm looking to measure the battery voltage. I'm using 2XAAA cells in serie (voltage range between 2V and 3V).
Below is the configuration to...
Sometimes, when I want to use the nrfjprog tool, I get the following error:
nrfjprog --log -f nrf52 --reset
ERROR: JLinkARM DLL reported an error. Try again. If error...
I cannot start Power Profiler Kit software. I followed the installing instructions, but ended up with the following:
>python.exe ppk.py
Traceback (most recent call last...
I'm developing for the NRF52 DK (nRF52832) using VisualGDB (which uses SDK v11.0.0).
Right now I'm facing two problems:
1. How do I properly handle interrupts while using...
There are tickets from 3 years ago that claim that nested CRITICAL_REGION_ENTER calls are not supported. Or they are supported if you write your own macros.
It appears to...
