Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
Hi everybody,
I was looking for a better way to update a data, like a 32-bit-word, without the need to erase the entire page. Part of this question is already been asked...
I was going through all the supported SDKs for the nrf52840 and in all of them, it is mentioned that the ESB and FreeRTOS support is not there yet. Could someone please let...
Hello, I'm trying to implement a buttonless DFU via ANT for a custom nRF52 board. I've got the 212 v4.02 Softdevice and I'm using the 14.0.0 SDK. I am able to transmit and...
Dear
i want to nrf52832 to collect accelaration sensor data（SPI communication 8MHZ）.
The sensor output datas per 250us,nrf52832 will lost the sensor interupt when 52832...
Good evening. I write a project on nrf51822 in which there are a number of services with a set of characteristics (write and read). I need to limit access to some characteristics...
Hello, I am working through the tutorials to understand how to better use the SDK. I am currently on the Advertising tutorial and have gotten a strange error that doesn't...
I'm developing an accurate and low drift millisecond-resolution timer on the NRF52. I'm limited to the resources on the NRF52 itself. Details of the system:
Initialise...
Is there anything special required to make a n52832 work the very first time the chip is programmed? Fuses to set, etc?
I'm new to nordic chips and I was handed a board...
While creating a DFU bootloader based on the bootloader_secure_ble example, I was having trouble getting a device to boot into DFU mode.
Initially the device would get...
(Sorry for the formatting. I don't know what's going on with it--the preview looks ok!)
I'm creating an application that uses
a modified version of the ble_nus
example...
Hello guys,
I have problem, I activate the BLE and connect it to my tablet application until then nothing wrong happens. But when I use sd_ble_gap_disconnect() to disconnect...
I plugged my nRF52 evaluation board to PC using a micro USB cable, dragged a ble_peripheral hex file from Nordic examples to the mounted JLINK drive, started up nRF Connect...
Hello,
I am using nRF SDK 12.2.0 , with nRF52832 on pca10040 hardware, and working with the example in examples/peripheral/spi/main.c to develop a driver for LIS2DE12....
In nrf51422, what is the behavior of these registers when an external rail-to-rail clock source is applied?
Do I have to issue HFCLKSTART? If
not needed, does issuing...
