after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Hi. I am a newbie in Nordic chips, quite knowledgeable in Atmel AVR, though. I'm working with an nRF51822 on a board like this www.waveshare.com/.../BLE400 . I use the Mbed...
This might seem like a really banal question, but i could need some clarification on this.
My understanding is that the config_client should be used on the network provisioner...
I want to connect a ST Chip (LSM6DSL - Datasheet ) via SPI with the nRF52840 Preview DK (SDK13) - NRF_DRV_SPI_MODE_0
When I am using the SPI Master example with different...
Hey Guys,
Thanks for this wonderful first of all.
Great work!
Well I am posting my first query related to Nordic mesh, please help
we need the BLE for our Wireless...
I would like to use connection handle value as index to an array which store some per connection specific data. Some questions about connection handle:
is connection...
I am using example DFU project (bootloader_secure) from SDK (12.3).
Chip 51822QFAA.
My problem is that I cannot start to debug session in Keil5. Use JLink.
I can program...
Hi
Is there someone who used polyfill under windows to run the thingy html5 example ?
( chrome and Bluetooth work around to have the application running)
Already thanks...
Hi,
I recently ordered the nRF DK 52 from Mouser Electronics (only one version available on their website). Furthermore, they were not able to provide me with the chip...
Hi,
I have been programming Nrf52 custom board using the J-Link in the nrf52Dk and Nrfgo studio.
Accidentally gave download to J-link from SES, The chip in the nrf52 gets...
Hi there,
Based on apple recommendation, I've chosen the next connection parameter set (and tested the parameter set works on other platform such as TI and Dialogue chip...
Hello All,
I am working with the HRS example. Currently I have one central device and one peripheral device is there.
From central code I want to print the updated RSSI...
I can't move higher than 12 as we still have builds for the NRF51.
I see migration sections for 13 and 14 in infocenter. I can't find anything for 12 and I do know that...
The ble_app_eddystone example that comes with the SDK uses the scheduler, but I have failed to see where any handlers are registered to the scheduler (and grep -ing the eddystone...
Thank you for viewing my question
nRF52832_PSv1.3, page 345, Idle current for UARTE (STARTED, no XXX activity)
What state uarte current consumption is only 1uA? How...
Hello ,
Regarding to mesh I have few more queries as below,
There are two types Bearer using which we can provision & configure Bluetooth Mesh Devices
GATT
...
