Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hello,
Have been reading the example codes and documentation in order to connect an ultrasonic
sensor to nRF52. The goal is to read in the value and then send it over...
Hi,
I am using nrf52dk and made beacon.
as nrf power profiler it should be around 16 uA but i get around 26 uA.
I have tried to get it in sleep mode for some hour and...
Hello,
I've a silly problem I cannot get rid of.
I've started from nRF5_SDK_11.0.0 ( devzone.nordicsemi.com/.../) and now I want to implement it in another example but...
Hi,
I'm working on getting the ble UART example running. I flashed the softdevice (s140), then programmed the board (pca10056) with the provided hex file, and encountered...
we connecting our hardware nordic nrf52 to mobile application but its is not showing any Bluetooth enabled devices |
please let me know about sdk and how to test
Thanks...
Hello All,
We are using nrf52840 board interface with wiznet550i.
We try to implement mqtt tls 1.2.we get following errors..
I get certificate verification error -0x2700...
Hi
I'm trying to implement the watchdog to my project, but I'm having some odd issues.
When I power cycle the device the watchdog works fine, but when I program the device...
I updated new firmware on nrf52. After that nrf52 was still visible "nrf Toolbox" Android app. It seems I didn't do anything wrong but when next time turned on nrf52 and scanned...
I am using nRF 52832 (softdevice v2.0). I am writing a code to get data via SPI and then transmit over BLE.
I have written my code and SPI is working perfectly.
But...
I'm new to using Nordic products and am trying to understand the difference b/t the soft device and the application in the context of the examples I'm running. Most importantly...
Hi, I have NRF52832 development board and NRF51824 beacon board. I want to dumb the code to NRF51 but i don't know whether we can use NRF52 DK to do the same(Supply to NRF52...
Trying to compile ble_app_cscs example, but have compiling errors in ble_cscs.c library.
Anybody have any ideas what is wrong?
Ubuntu 16.04, NRF SDK 12.3, GCC 7.2.1
Terminal...
Hi all,
I need to send the information from 2-5 sensors in a room. The sensors are placed 2-3 meters far from each other. Each sensor has a BLE, using a battery and generates...
