Dear all,
after cutting the SB bridge to the QSPI chip and close the ones to get the pin free and disabled also qspi inside the nRF52840dk_nrf52840.overlay file I'm unable...
Dear all,
I stubled upon the following issue when developing a BLE sensor product. When I try to bt_gatt_notify(); With only one characteristic, there is not an issue...
I was looking into the sdk provided by nordic for nrd52840Dk board and want to test the zigbee protocol. I havn't find any sdk for that.
Can you share me some links and...
Hello Team,
I want to configure P2.07 as UART RX for my custom board.
But when I clear the already assigned property as led2 for this pins from the pin editor gui, I am...
Hi,
I am trying to adding a coded phy support on my device in NCS project.
once I added CONFIG_BT_CTLR_PHY_CODED =y in my config , the ROM size will add more than 7kB...
Hi all !!!
I understand Output OOB, Input OOB.
I case of No OOB, value which is attached to Confirmation value is 0x00, what happens in case of static OOB?
Hi there~~ I'm trying to create a voice streaming application with the Mesh and the Nordic Thingy:52 I downloaded both the nRF5 SDK 14.2 & Mesk v1.0 to test the Mesh's light_switch...
Hi everyone,
Currently, my team is developing a BLE keyboard which uses 6KRO protocol. Are there any examples for the 6KRO protocol using nRF52 chips?
Thanks!
Update:
Hi again to everyone!
After a while, I've received a new custom board and a new cable to connect through P19. But everything are not working again.
Now, in...
I have a 12 MHz voltage controlled oscillator driving the nRF9E5 at pin xc1 and xc2 is open will this pose a problem for running the nRF9E5? The clock has a +-50ppm stability...
I am working on a project that requires me to wirelessly communicate with and program a left hand Oculus Touch controller, since dismantling it will cause damage. The controller...
I see I have more than 100 free pages (~ 101 KB) on Nrf51822 with SD130 but how can I assign all of them to the FDS module. I am going to manage a database with FDS on the...
Hello,
I am trying to use PCA10000 dongle with the pb-ble-driver-py libraries with absolutely no success, as I get a "Failed to open. Error code: 13" error.
I am running...
Hi, please!
The question is related to "nRF24L01P_Product_Specification_1_0.pdf" datasheet in " www.nordicsemi.com/.../nRF24L01P_Product_Specification_1_0.pdf" and to NRF24L01P...
Hello. Engineers.
I'm a beginner in nRF52832, I'm looking for someone who can help me.
I have nRF52832 development kit. I tried examples blankly with SDK14.0.
It working...
Hi,
I've recently come across a problem where in some cases my device's memory gets trashed.
Ideally I'd be able to set a watchpoint on a memory location so that I could...
main.c
I am working in sdk14.1 nrf52832 ble_app_uart_pca10040_s132 and ble_app_uart_c_pca10040_s132.
ble_app_uart_pca10040_s132:
nrf_ble_gatt_att_mtu_periph_set(&m_gatt...
Hi,
I'm using nRF52810 on SDKv14.2 and I have changed the bootloader from 52832 to work for 52810. I could do OTA now. I found that the bootloader there is no timeout when...
We are developing a test jig that also programs the Nordic nRF51822 on our board.
We are receiving the following error message from the command line programmer:
NRFJPROG...
