Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
I'm getting a weird behaviour on my first NRF52 custom board. It's a BLE with HR, battery and a custom service. After programming I can test it properly with/without debugger...
Hi,
I am using SDK 14.0 on nRF52840 (DK), with sofdevice enabled and FreeRTOS port.
My question reagrds the "blocking mode" transfer - event handler was not provided...
I have four PCA10056 Development Boards and I downloaded the SDK for BLE Mesh. The examples, however, only work with the PCA10040 boards. I have tried redefining the board...
Hi all,
We are ready to have our product released and need to have it tested and certified for release in the following markets:
North America = FCC IC
Europe...
Hello,
I would like to configure the NRF51822 as a Peripheral to receive data from a smart phone, and then call a routine when the receive process has been terminated....
I'm using the nrf52832 and I need to stream audio from an SPI connected memory chip, to an I2S connected amplifier. Is there a way I can have the SPI device stream data directly...
Hello,
i have the following setup: nrf52 as peripheral, smartphone as central.
Peripheral's purpose is to be an interface between appliance and smartphone. It has no pairing...
Hello,
For more "simplicity" I have devised my own OTA update procedure. It relies on image information being embedded in a dedicated section (I have modified the linker...
Hello,
I have succesfuly used ble_app_hrs--longwrite examples provided in dev zone to receive >20bytes from NRF Connect with my pca10028 board. How can I send >20 bytes...
Hello
I am trying to build a project, the problem is that the project is not linking properly, it compiles for sure. During link process I have this errors:
C:\nrf52\workspace...
Some questions regarding offset calibration when doing single samples (or burst mode) from multiple input pins:
Can SAADC offset calibration be performed after SAADC...
I am developing a BLE peripheral application on nRF52832 and SDK 14.3.
I have been power profiling my application and quite happy with the results, except for when the...
Hi there,
I was trying to understand "sleep" power modes of the chip (CPU + Peripherals) in a bit more details - but my understanding is that everything is handled by the...
Hi,
I am facing some issues on enabling timer1 with s132 (nrf52832 pca10040) enabled. i am using the basic timer0 example code as reference and it was working without the...
