Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi,
I am working on my production hardware with nRF52840 on it. I am using MBED OS. What should be the memory map of 52840 for soft device and Application code? I am using...
Here are my system requirements:
A single "Controller" needs to send 4 bytes of data per node.
There are 25 nodes in a system (100 bytes total payload).
All nodes must...
Hello,
Is it possible to use Mesh SDK and create a GATT database for mobile device to connect to? There are no examples for this in Mesh 1.0.0 and 1.0.1 except a simple...
Devzone,
I'm working with the nrf51822 dev kit- specifically with master emuator API version 2.1.8.
Does this current release of the API (2.1.8) or subsequent releases...
Hi Everyone. I am Anthony, embedded software engineer. Now I need to dive into the Nordic BLE world for the new project. And we are going to used nRF51822 MCU. But I have...
Hi there,
On my project I was working using sd_flash_xxx functions to write the whole flash pages or erase it, so I added peer manager to my project and I had to switch...
Hi,
We have a specific feature that isn't supported by iOS, and we'd like to turn it off when connected to iOS devices to reduce battery usage.
Using the nRF sniffer we...
Hello,
Currently working on a project for a company that uses your product.
Does Nordic use a certain style guide, or do they have a style guide internally that I could...
Hi Folks,
I'm using the Custom board with nRF52 and temperature sensor .
I'm trying the Experimental_App_Peripheral_Blinky code in the custom Board but i couldn't able...
Equipment: PCA10040 DK with SDK14
I'm currently having the same issue described in this post.
Essentially, I can program and build my project correctly in Eclipse, but...
Hello,
I have the following questions about the SAADC of nRF52832:
The relationship between ADC code and result.
For 0.6V reference, 12-bit resolution and single...
I'm writing an Android application that connects to a physical device via BLE. Android app will act as peripheral role while the device is central (with a BLE113 module inside...
Hi,
I have just started using a nRF52840 PDK board with the purpose to verify BT 5.0 features. I am completely beginner working with nRF boards or nRF SDK. Anyways, I downloaded...
Hello, I am working on optimizing the power consumption of our application.
I have got two design decisions that I would like to ask for some advises and opinions on.
...
hello,
I uses NRF51822 to make a beacon with RTC.
When it works initially, the churrent is small about 330uA，but after a few minutes it becomes 1.1mA and stable.
I donn...
