Hi there is a problem in github.com/.../nrf51-UART-examples
any one can help?
I put empty loop in main, and comment off all ble related int. and I process uart_evt by...
Hi,everybody！
When i install master control panel 3.10.0.14, i can't find nrf.exe in " C:\Program Files\Nordic Semiconductor\Master Control Panel\3.10.0.14\nrf ". Only nrfutil...
Hi,
I've been using the nRF51 dev kit, and today it stopped mounting when I plug it in. It doesn't show up as MBED or BOOTLOADER.
I use both Mac OS X and Windows, though...
SDK_9.0.0
I was trying to implement 2 different UART connection parameters so I decide to use re-initialization.
My initial parameters included APP_UART_FLOW_CONTROL_LOW_POWER...
I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
I am working on an automation project wherein I have to integrate ESP8266 with nRF51SDK. So, I want to serially send and receive strings over a physical UART connection, not...
Hello All
For our project we are using teensy3.6 as our main micro controller unit and NRF24L01 as RF transmission device.
Our project include mainly 2 parts
1) Data...
Hi. I've encountered a problem with some of my nrf24le1 chip (near every 5th piece) - current in deep sleep mode is very high (30-80 uA), if i change it to another chip, then...
Does the ui depend on the app design(nrf connect app) or on writing data in the characteristics. For the predifined i am getting a switch but for the one i added i have to...
Dear sir,
Sir I am trying to send an array of 40 values via nrf51422 to your andriod app "BLE SCANNER" by using the function "ble_nus_string_send ". But it is sending only...
I've tried ble_app_uart, nrf_serial.c etc. and none seems satisfactory.
I can write to the logger logger/uart during DEBUG, but it doesn't seem to succeed in RUN.
Question...
Hello,
I'm using :
- SDK 11 s132
- nRF52832
I want to protect my flash against dumping from swd but I'm working also with DFU from our custom app.
Is it possible...
Randomly on my nrf52832, sd_power_system_off() is returning NRF_ERROR_NOT_SUPPORTED and I'm looking for tips on how to figure out why. I'm using a Bluetooth soft device and...
Hello,
May I please check if the following is correct? On the nRF52840-PDK board (v0.9.3, 2017.47), the "VTref" pin of the "Debug In" header is connected to VDD. Should...
I need to upgrade and existing nrf51 S110 system based on SDK 8.x to something that supports the same functionality and also supports both a nrf51 (during the transition)...
I am working on a project where we are using a nordic bluetooth chip and connecting it to a RS485 Bus using UART with Baudrate 115200. The messages sent from the Bluetooth...
I want to experiment with BLE Mesh. I have several BLE400's with nrf51822's. I want to use these as mesh nodes. I want to get the nrf52-dk to use as an interface node. Can...
I recently downloaded Segger's Embedded Studio to compare its performance and ease of use with IAR Embedded Workbench. We have a kickstarter version of IAR for ARM which has...
hi,
i am using nrf5 sdk 14.2.0 ble_app_uart example with keil v5 IDE and i am doing coexistence with nrf5 sdk for mesh v 1.0.1 for nrf52832 mcu.
a have done all steps...
