Hi,
I am trying to run nRF24L01+ in default configuration using simple ping-pong examples using RF24 Arduino library.
The problem is that while ping-pong is getting through...
Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
I am trying to understand the Passkey LESC pairing on S140 soft device using the latest SDK 14.0.2.
The message sequence charts has a block "App starts DHKey calculation...
Hi developer, sorry to interrupt and ask. How to use an ultrasonic sensor with nRF52? Since I search a code for nRF52 are not exist and see ultrasonic sensor can connect with...
I modified TWI_SENSOR_PCA10040 example from 14.10 SDK to run on my NRF52832 device, and it reads from the device address perfectly. However when I wrap reading inside a FreeRTOS...
Hello ,
What is the preferable way to flash code into NRF52832 IC during mass production? Flashing the code into custom IC with NRF52-DK in time consuming process.
And...
Hi,
All of a sudden (isn't it always the case :) the JLink debugger fails to flash the app code to the dev kit (PCA100028)
The Project's softdevice is flashing well without...
I have configured 3 differential ADC channels
to sample with timer/PPI/DMA buffer.
When I turned everything off, I couldn't get below
20uA current (with only LFCLK running...
2017-12-07 22_28_04-D__Users_Eyal_myWorkspaces_KeilMDK_ble_peripheral_ble_app_hrs_rtx_pca10028_s130_.png
Hi,
I've developed a BLE Central app based on the SDK HRS collector...
Hello,
I am using NRF52 TWI master to read data from my sensor, I have read the twi_sensor example but it doesn't make use of nrf_drv_twi_xfer() .
My question is quite...
Dear nordic employee
1、when I use the spim to send 1 byte address to read it's value(4 bytes)，like this：
nrf_drv_spi_ transfer(&spi,headerBuffer,(uint8_t)headerLength...
Hi!
I use this debug on another examples fine. But want to enable this debug in a my project. In a config.h file RTT debug enabled. But doesn't work debug. I remarked that...
Hello All,
Please check above image, showing antenna layout of my custom board.
I am receiving error frames at ~40ft distance on sniffer.
Please check whether antenna...
When creating a custom bootloader for buttonless DFU, it is surprising to see that nrf_dfu.c not compile without defining button related function.
The warning
nRF5_SDK_14...
After succesfull compile, installation and run of my first application , I cannot see anymore the nRF52 DK board from windows.
The application keep flashing the led but no...
I wanted to share the most reliable and efficient method I found to collect and store my log outputs through segger RTT, which also allows using the excellent Log Viewer Log4View...
Hello all:
I have faced a problem that my device will report hard fault when I try to start advertising after force disconnect the device.
My EV board is nRF52832 and...
