I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
Hello nordic dev community,
I am completely new to nordic products. I attended one of the conference and got more information regarding developer zone and info center....
Hi,
I am wondering why the ccm library uses the software aes encryption. Is there anything wrong with the hardware encryption so that it should not be used?
Marius
Hi there,
hope you are doing fine.
I am using SDK 14.1 with SoftDevice 132 as well as a state machine framework which needs a have a function called periodically to...
Hi. I'm using nRF52832, SDK13.0.0 as peripheral.
When I want to disconnect central, I'm using sd_ble_gap_disconnect function as below.
err_code = sd_ble_gap_disconnect...
When I try to build and run any example from the nRF5 SDK, it can compile successfully. But when loading to the eval kit, it can't find the 's140_nrf52840_5.0.0-2_alpha_softdevice...
Hello Everyone,
I am using nrf51822 256Kb Flash and 32KB RAM Raytac's BLE module with SDK11, S130 with over the air Bootloader (16Kb).
So the aim is that when a particular...
Hi all,
I encountered a problem , when I connect 1 board central to 2 board peripheral via NUS . It connected and discovery success . But at
static void db_disc_handler...
I was compiling a project(ble_app_uart and I am using PCA10028), it was not successful and KEIL5 display this:
it looks like I didn't install NordicSemiconductor.nRF_DeviceFamilyPack...
Hello,
I use a nRF52832 device, and I have some strange behavior when I use PWM. You can see my test program listed below.
Thank for your reply, Thierry!
/*
* Test_PWM...
Hi. I am a newbie in Nordic chips, quite knowledgeable in Atmel AVR, though. I'm working with an nRF51822 on a board like this www.waveshare.com/.../BLE400 . I use the Mbed...
This might seem like a really banal question, but i could need some clarification on this.
My understanding is that the config_client should be used on the network provisioner...
I want to connect a ST Chip (LSM6DSL - Datasheet ) via SPI with the nRF52840 Preview DK (SDK13) - NRF_DRV_SPI_MODE_0
When I am using the SPI Master example with different...
Hey Guys,
Thanks for this wonderful first of all.
Great work!
Well I am posting my first query related to Nordic mesh, please help
we need the BLE for our Wireless...
I would like to use connection handle value as index to an array which store some per connection specific data. Some questions about connection handle:
is connection...
