Are there any migration guides for a customer who wants to migrate from nRF5340 to nRF54L15? And if they are nRF54L15 in chipscale, anything they should be aware of including...
We need to sense temperatures in the upper end of the operating range, specifically in the 40C to 70C realm. We have three different units, and we are finding that the temp...
Hi,
We're evaluating NFC for our project.
I've been testing with a nRF52840DK - PCA10056 Version 3.0.2.
Using the antenna supplied with the Development Kit I am...
Hi,
I have been playing around with the configs but I could not get Mode-3 to activate. What should I change for cs configs and the prj.conf file in order to activate it...
Hello - We're designing a new app for our product in Flutter. I was writing the proof of concept for the firmware updates, but I hit a roadblock with a Mcu Mgr Error: 25 ...
Hi there,
I am using an NRF54L15 custom board and am trying to set up a functionality using DPPI + PPIB. using a single in (1 event) and single out (1 task). I have two...
Hi,
I'm trying to get the debugger to work on my target board. I created the attached simple program to eliminate complexity.
The debugger starts, but it starts running...
Hello,
I've connected the nRF8001 module and a light sensor to a microcontroller.
Actually I can read data only when I send a string from my smartphone but I want to...
I'm able to program the Soft Device (s110_nrf51822_7.1.0_softdevice.hex) from nRFGo studio and the compare is fine, but when I go to Keil uVision 5, I can build ble_app_beacon...
I use S130 on two nrf51822/PCA10001 boards. Each nRF scans and advertises simultaneously.
Scan parameters are:
scan_param.active = 0;
scan_param.selective = 0;
scan_param...
Is there a port of lib_aci for 16-bit processors? The structs in lib_aci written for nRF8200 are byte misaligned using a 16-bit processor. Seems to be almost a complete rewrite...
Hello,
I try to generate 4 PWM signals on an nRF51 DK board, but I have two troubles :
in the "Simple PWM", during nrf_pwm_set_value() function the TIMER is stopped...
Hi,
I recently ordered a usb dongle. It has PCA10031 board. The chip shows "N51422 QF ACAB" printed on it.
What SDK should I use? 6.1.0?
What board file should...
Hi!
I am using nRF51 SDK v6.10. I try to analysis the "spi_master_example". Source codes is
working well. But I couldn't understand how the "spi_master_send_recv_irq(...
I have an android application, which one can set and unset the LEDs of my nRF51422 EK. But sometimes when I click to fast the command will not be send. So I would like to...
Hello,
I want to know if it is possible to configure a button to act with different Detection delay.
In other words I want to have a single button to be able to trigger...
Do we have KiCad version of nRF51822 QFN48 reference design? We looking at open source toolkits, including Eclipse, so KiCad comes into picture.
Thank you in advance!
The test code:
int main(void)
{
sd_softdevice_enable(NRF_CLOCK_LFCLKSRC_RC_250_PPM_250MS_CALIBRATION, softdevice_assertion_handle);
temp_init();
unsigned int aaa...
I have a follow-up to this question: devzone.nordicsemi.com/.../
We are interested in dynamically changing the supply voltage because our space-constrained design requires...
Hi,
For my custom PCB, I am using the PCA10004 as reference in order to determine if the maximum possible range has been achieved. However, I am seeing only about 20 feet...
Hello I'v just ordered a NRF51-DK kit.
I'm looking at the different tool chain. In my application speed is critical 16Mhz is actually bearly enough, so my question is:...
I have a USB dongle with an nRF24LU1p that has a few SPI pins but is missing the RESET pin. I would like to be able to program it via SPI but the SPI programming protocol...
