I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hello!
So I can connect, disconnect and write to my applications characteristics via a PyQt5 GUI I threw together. On the python backend, I use Bleak to
search for devices...
Hi, I am developing using nrf52832 and st7735s.
Successfully displayed the lcd screen using the code in \examples\peripheral\gfx
However, when screen clear, text_8print...
Hi,
I am developing a multi-protocol communication device using BLE, ANT and 868Mhz "long-range" communication. I am using MRF49XA chip for sub-ghz communication. I have...
I have just updated to the latest SDK, including the S110 Soft device v7.0.0.
I have now noticed that I can bond using the Master Control Panel, but I cannot bond using...
On June 25th I asked a private question regarding be able to use the S110 soft device with the nRF51422. The following is the response I got:
....
Yes you can use the...
I am unable to to send notification for a customized service. I am testing a customized services that simply increments a variable every 3 seconds and sends notification with...
Hi guys,
I am trying to use the timer 1 on the nrf51822. I found the sample code online which could probably do the job for me. But I wanted to know what is the standard...
Hey Guys,
i asked this question already few days ago, but today i produced a log-file.
The procedure was:
Setup: SDKv6.0, SoftDevice v7.0.0, nrf51822
empty board...
Hi guys,
I had look at the ble_connectivity example in \nrf51822\Board\nrf6310\s110\ble_connectivity floader,but I can't found any documentation about this project.Is it...
Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
We found that in some cases. e.g. we started a background ble service. The ancs characteristics will change as the picture below. Do you think it's normal? Does the Nordic...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi guys,
i'm just porting my app from SDK5.2+SDv6.0.0 to SDK6.0+SDv7.0.0 and stuck with the device manager. There rises some questions, and i hope someone can help me....
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
Hello,
About TWI in "nRF51_Reference_manual_v1.1.pdf",there is a register called "SHORTS".
I have a few question about this register:
Can I use SHORTS register to...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
