Hi Nordic：
We are currently testing Zigbee on the nRF54L15 platform using the Zigbee R23-add-on-V1.0.0 SDK. It has been observed that when a low-power node disconnects from...
Hello, I am using ISP1907 which has NRF52833. I get the IQ data and configuration from serial as: DF_BEGIN ['IQ', 0, 0, 11, -9, -213] ['IQ', 1, 8, 11, -209, 23] ['IQ', 2,...
I have 2x Power Profiler Kit II up and running using the Power Profiler app - started twice and with separate PPK2 instances selected, as described in another support post...
Hi, I am running openthread on the NRF54l15 DK. Whenever I am debugging and hit the breakpoint or pause the program, then on resumption my app crashes. How Can I debug while...
Hi everyone,
I'm working on a project using the Nordic nRF5340 microcontroller and I need to count both rising and falling edges of a square wave signal on pin P0. 14, coming...
Hello, I’m working with a combination of nRF5340 + nRF7002 + NPM1300 , and I’ve only changed the I2C pins connected to the NPM1300 to sda pgio1.4 and scl gpio1.6 .
SDK...
I am running into a secure fault when I set the NVS_SECTOR_COUNT to >= 7, not sure how to proceed.
it fails at nvs_mount(&fs)
I have added a nvs_storage partitation...
I find this function.
tx
void ble_send(uint8_t * data, uint8_t length)
{
ble_nus_send_string(&m_nus, data,length);
}
ble_send(&data_array[0],10);
but I don...
Hi, I'm trying to run ESB during the timeslot api requested slots.
The problem is that BLE uses app_timer, which uses SWI0 for the callbacks, and at the same time, ESB also...
Hey , I am working on nordic nRF51822 chip and using it as an iBeacon. I want to send some custom data apart from UUID,major,minor in the packet. How can I send it ?
As in...
When I try to set a breakpoint in eclipse by clicking on a line, gdb tells me in the eclipse "Console" window below the code: "No symbol table is loaded. Use the "file" command...
Hello,
I have three custom services. I wanted to add descriptions to the characteristics for easier testing and debug, so I used the typical method to add descriptions...
Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi
I'm trying to test UART over BLE using the nRF51-DK and the sample code "ble_app_uart_s110_pca10028 (nRF51 PCA10028)" along with both the nRF UART APP for both Android...
I'm using nRF51822 SoC , is it possible to change the major value when i push the button ? I tried simple assignment but it didn't work so i ask if i have to use the function...
hi,
i have kept RAM block 0 and RAM block 1 on in OFF mode by calling "sd_power_ramon_set(0xf000f)" before entering off mode ,i saw the value of RAMON register is 0x00030003...
I'm using nRF51822 SoC . I wanna read and write from the flash memory . Shall I use a specific configuration before using read and write functions provided from S110 softDevice...
we have created ble mesh, and data through ble nodes is passed every 5 seconds, but nodes gets disconnected with reason BLE_HCI_CONN_FAILED_TO_BE_ESTABLISHED??
please someone...
we have created ble mesh, and data through ble nodes is passed every 5 seconds, but nodes gets disconnected with reason BLE_HCI_REMOTE_USER_TERMINATED_CONNECTION??
please...
we have created ble mesh, and data through ble nodes is passed every 5 seconds, but nodes gets disconnected with reason BLE_HCI_CONNECTION_TIMEOUT?
please someone give...
we have created ble mesh, and data through ble nodes is passed every 5 seconds, but nodes gets disconnected with reason BLE_HCI_LOCAL_HOST_TERMINATED_CONNECTION?
please...
