Good afternoon! As the NRF7002 takes about 400ms to start up from shutdown, we would like to use the very low power deep sleep function for quick startup. Unfortunately, due...
Good afternoon! As the NRF7002 takes about 400ms to start up from shutdown, we would like to use the very low power deep sleep function for quick startup. Unfortunately, due...
Hi,
I would like to know the difference between the nRF52840-QIAA & nRF52840-QIAA -R7.
What is the significance of R7 here. Not able to find it in any conclusion ...
Hi, I'm working with the DWM3001CDK (nRF52833 + DW3110) and currently using SPI to interface with the DW3110 for UWB communication.
I'm trying to use a second UART to communicate...
Hi I am developing in 54L15. Now use DPPI to link
TIMER10's PUBLISH_COMPARE[3] ---> RADIO SUBSCRIBE_STOP,
it works fine.
Now I want to trigger a GPIO signal through...
Hello, I have an issue regarding the current measurement of my nRF7002DK_nRF5340. I am trying to measure the current consumed during the transmission of a carrier on a Wi...
Post:
Hi Nordic Team,
We are currently developing a product based on the Raytac MDBT50Q-1MV2 module, which integrates the nRF52840 SoC. Our firmware is built using the...
I'm just getting started with the nRF51 Eval Kit, I have the 5.1 SDK installed, using Mac OS X for development. I also have the GCC ARM toolchain installed. Firstly, I had...
Folks,
I have the S110_SoftDevice_Specification v1.1 (great doc, thanks) and the doxygen-generated API docs. But is there an App Note or other document that fills the void...
Description of my system:
Hardware:nRF51822, pca10001
Software: SDK5.20, S120
If i first call the function ble_stack_init(); and then i open the LFCLK first by set...
Hi,
I'm working with the heart rate demo for the nRF51822 Development Kit and I can only connect and discover with the development dongle and master control panel. If I...
Hi,
I use ble_app_uart project (pca10001) and new softdevice7.
I find a DFU project at nrf6310 directory of SDK .
when i program both projects the uart application...
I am aware of L2CAP API exposed by the SoftDevice SDK sd_ble_l2cap_cid_register(...)
How can I find out if this API will create a connection-oriented and dedicated channel...
Hello!
I would like to use the nRF51822 and build a pcb design in Eagle. While i tried to create a new package i couldn't find any specification for the qfn-48 6x6 the...
1.description of my system:
Hardware:nrf51822,pca10001
Software:sdk5.20,run the softdevice s120
2.the problem i meet,in the main() function
the first i called the function...
Hi,
We are using nRF51822 BLE device in our product. As we got to know that this chip cannot be factory programmed.
Can you please suggest us how we can program this...
Does the following flasher also allow to debug the nRF51822 device?
Segger Flasher Portable
If not... which flasher/debugger is suitable to be used during development...
I'm adding the bond manager to an existing nRF51822 s110 soft device project to enable encryption when reading/writing certain characteristics of a BLE service.
As far...
i am making something about dfu!
i read some message from "readme.txt"
such as :
Program initial SoftDevice
Make sure the device is cleared (nrfjprog --eraseall...
I have trying my best to find the url of ''nrf51_sdk_v6_0_0_43681.msi'，but there is nothing i got, i need some help.
Do you know somthing about it? thanks!
Edit: One...
