I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hello all,
I am getting an error when my device disconnects from the client. The error occurs while bond storage due to data limit exceeds.
err_code = ble_bondmngr_bonded_centrals_store...
Hi all,
I have made some modifications to the bootloader example project (dfu_dual_bank_ble, s110) to get a bootloader that meets my requirements. It is working ok, I can...
I debugging some function abnormal after OTA problem, and problem with disappear after redo OTA FW upgrade, duirng it I found a problem about Master Control Panel FW upgrade...
From the datasheet, the On mode with all blocks idle draws 2.6 uA.
In my code for the PCA10001, I immediately set:
void sleep(void)
{
__SEV();
__WFE();
__WFE();...
I was going through online material all of which mention that the profiles and protocols (GAP,GATT,L2CAP) i.e. the host for a BLE implementation is a software stack rather...
Hello - I have gotten blinky_example up and running in eclipse using the SDK 5.2, nan-29, and some additional google-fu.
Now when I press debug and the play button, it...
I am trying to use nRF UART app and nRF8001 chip. But I cannot change the device name. I intend to change the device name after nRF UART app detects the device. Plus when...
I'm trying to create a method so a users can initiate an OTA update from a paired device. To that end I've written something which is supposed to invalidate the data at the...
I'd tried some first steps using nRF Sniffer on a linux host.
Within sniffer_uart_protocol.xlsx I read something about the Uart packet format et cetera.
I'd programmed...
I am trying to get ble_app_beacon exampel working on the PCA10001 on my nrf51822 working. However when I simply run and reach APP_ERROR_CHECK(err_code) inside "advertising_init...
Reading through the nRF51822 Beacon reference design it states that there are Keil ARM project files available. Does this mean that the example code given after purchasing...
Hi all。
I am programming a nRF51822 chip, using the S110-nRF51822_6.0.0 soft device,download ble_app_hrs.hex。
I used app name "nRF Utility".I can connection nRF51822...
Hi,
i have some more, for me fundamental, questions and i hope some one can help me :)
1.) can i use the advertise function whenever i want or only in connection interval...
Hi All,
can any one please share information related to this
1)please explain clearly about channels and pin?
2)can 2 gpio pins hooked to a single gpio channel?...
