Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
Hello,
I'm modyfiyng a NUS template. I noticed, that when I move to far with my Android phone (with the nRF UART v2.0 app) from the NRF51 PCA10000 board, it disconnects...
The above mentioned example ( here ) is the one that is available in GitHub.
I want to implement bonding with static passkey based on SD110 v8 and nRF51822 with Device Manager...
I've tried to drop in all non-main code from the spi 5W example into my program and I keep getting the following errors:
.\_build\nrf51422_xxac_s110.axf: Error: L6218E...
Hi -
Looking for a layout review of the NRF51822 antenna and oscillator design attached. The two main questions are:
Is it recommended to remove the copper ground...
Hi,
any plans to release firmware package for nrf51822 smart beacon using Soft device 8 and SDK 8? Thinking I better ask before I start adapting it on my own.
thanks...
What is the pinout on the DEBUG OUT-pins?
How do I adapt the code to work both with dev board and an external chip?
There are BSP stuff I probably can't use that I use for...
I am using S110 7.1.0 which I know has the ability to unblock the CPU during Radio Event. However I would like to do the opposite and increase the time between a Radio event...
Any news on the new specification for S130?
I am trying to find out the concurrent power profile. It the power management section it said that it has not be characterized...
Well, I've ordered my preview nRF52-DK and might get it by the weekend. I have not been able to find the schematics and design files on the main Nordic site, or the new infocenter...
This project is a HRS example from latest SDK, without any modification. I use nrf51 DK board. WHen I debug, I get hardfault after some type. Try to run the code under debugger...
Hi,
we used NRF_UARTE_Type POWER for the "peripheral power control" of the UART interface on nrf51 - works fine.
After trying to port the nrf51 to nrf52 I found out...
The question is: how to completely turn off PWM in SoftDevice?
I am using the libraries nrf_pwm.h and nrf_pwm.c in this repo for PWM with SoftDevice. Everything seems to...
Hi,
when trying to update the firmware with current nRF Master Control Panel (version 1.10), the update finishes successfully, but the firmware does not run.
The problem...
