Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I'm trying the example in the SDK v0.9.1: examples\spi_master
When I load the project, build it, and debug it, all that happens is that it goes into a failed state where...
I occasionally get an NRF_ERROR_NO_MEM error when trying to add a custom characteristic. I'm only using 3860 bytes of ZI data, stack = 2048, heap = 2048 so it seems like I...
Hi
I am working on the ble_central_and_peripheral example in nRF51_SDK_8.1.0_b6ed55f .In this example it is possible for us to connect to 3 peripherals only.But we would...
Hi, are there any examples in C for how to directly access the registers on the chip? I realize this is a super basic question, but all the register access in the examples...
Hi,guys
I set BLE parameters like this:
#define MIN_CONN_INTERVAL MSEC_TO_UNITS(500, UNIT_1_25_MS)
#define MAX_CONN_INTERVAL MSEC_TO_UNITS(1000, UNIT_1_25_MS)
#define...
Hi,
I'm using sd_ble_gap_connect to connect to a set of known address and whitelisted devices. My central periodically (once an hour) needs to check on a known set of devices...
Hello,
I'm looking for electrical parameters in nRF52832_OPS_v0.6.pdf but I didn't find typical impedance values for analog inputs .
Also not found any value for RESP and...
Suppose I defined services (According to nAN36 Document)
#define BASE_UUID {}
#define SERVICE1 1602 // This service send a alert message Id i.e. similar to proximity hex...
hello,
I am working on the example ble_central_and_peripheral in nRF51_SDK_8.1.0_b6ed55f.I can connect the device to master control panel in the computer and discover services...
Hi all,
I am trying to update the bootloader, softdevice and application all in a ZIP package through DFU, and at 99% after upload it stop and throws the error:
...
Dear Engineer:
I am a developer of the nRF51822;Some costomers want to send a large number data over the bluetooth,So they require a high quality in speed;I want to know...
Hello,
I've noticed that it is quite hard to set up an Eclipse development environment and I want to try to make a package of everything that is needed for developing with...
