Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
I created xml file for heartrate server using bluetooth developer studio and the plugin nRF8001_Arduino (plugin nordic semiconductor for arduino)
the generated xml file...
I read this older post ( devzone.nordicsemi.com/.../) and have a similar issue but with enough differences that I felt it was worth a new question.
I have an STM32 MCU...
I have enabled data ready interrupt bit and also enabled the fifo bit and also enabled gyro_fifo and accel_fifo bits in mpu6050 so that when data ready interrupt occurs the...
I have a nRF51DK. The Softdevice on the board is S110.
I load the ble_app_template from the SDK 8.1 on the chip. It builds with success. Now with the MCP I am able to see...
I'm now using the lastest SDK 8.1.
I found that if I call app_button_enable() after app_button_disable(), app_button_enable() would not function again.
But if I changed...
Hi all,
I read that the nRF51822 comes as a blank chip from the factory, and this means that we have to program the SoftDevice ourself. I am wondering if this is the only...
Hi,
I'm using the Rigado BMD-200 Eval Board with sdk 8.1 and am running the ble_peripheral example titled ble_app_uart. I am using my iphone and the nRF UART app to communicate...
If using the button handling library the #define GPIOTE_CONFIG_NUM_LOW_POWER_EVENTS needs to be changed to add number of buttons being handled.
This wasn't clear to me...
Hi,all. i want to set tx power use interface "ble_tps_tx_power_level_set",and read back tx power level used tps servoce on my phone.how to do that ?Thanks for your reply!
Int the website:
link text
FEATURES show the nordice nRF51822 has 3 data rates (2Mbps/1Mbps/250kbps).
But , I set
number of packets transmitted per connection...
Hi,
If I want to run a blocked task e.g. write 1MB data to the external flash size 8MB(NVRAM), that it takes 3 seconds. What is the best way to to in NRF 51822?
Do you...
Hi,
I'm using the softdevice s110.
The power consumption is sometimes a little weird (around 1 mA). I think that the chip is in debug mode.
How can I know if the chip...
Hi,
The datasheet for nRF52 has pin assignments for QFN-48 only at present.
I'm using WLCSP package for the nRF51 and would like to know if there is any pin-to-pin compatibility...
have anyone successfully NRF51x,NRF52x series to interface with Matlab? Do you need to develop any additional code to do this?
Currently Matlab has support for BT Classic...
Hi,
I'd like to embed the nrf.exe utility used for creating DFU packages and uploading firmware via serial in a 3rd party app for use with our Nordic based devices.
...
