Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I am running Windows 7 Pro SP 1 64 bit and have gong through the tools installation procedure, in particular running nRFTools_7_7_0_Installer.exe. This ran the J-Link V5.02...
I am completely confused by the nRF51 UART. I'm trying to port code originally written for an STM32 (another cortex chip). There, I define an interrupt, enable the RXRDY or...
Hi,
I need to have two different interrupt handler for one pin?
For LOTOHI one handler and for HITOLO another handler, how to do that?
Here is what i did until now...
Hello Nordic and fellow developers
While implementing bonding into an application based on S130 I found it necessary to test on the role of a given connection. Different...
I am getting device id of peripheral on central and then getting it displayed on hypertermianl hyperterminal using ble app multilink perihperal code with multilink central...
Hi Everyone,
I have what I hope is a simple questions. I am creating a piece of hardware that will act as the peripheral to a central iOS app in regards to a standard BLE...
Is there any construction available in the SDK, to achieve printing functions, with an undefined number of parameters ? The classic example :
#ifdef CONFIG_DEBUG
#define...
Hello,
I've ready the final S130 spefication and it states that the advertiser is started as early as possible and that i runs asynchronously to all other roles. Now I...
Calling app_sched_event_put() from the NRF_RADIO_CALLBACK_SIGNAL_TYPE_START signal handler causes a crash due to the CRITICAL_REGION_ENTER() call inside of app_sched_event_put...
is there any code for device which act as master and peripheral other than nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental \app_s130_demo\pca10028...
I have a simple nRF51822 BLE application where a voltage is read by ADC periodically, and several values are sampled and averaged. However, from time to time, I get another...
Hello All ,
I am working on nrf51822 with sdk 7.1.0 and softdevice 7.1.0 .Earlier my ble connection was working very good with no disconnection anytime unless i disconnect...
Now I'm working with MCP 3.9.0.
When any device is connected, characteristic default values are not 0's. Can they be initialized in any way? It is a little bit annoying when...
Is there a separate reference resign for the 1.8V of operation (as in case of nrf51)? Or it's implicit and the chip can be powered in range of 1.7V - 3.6V.
Thank you!
I am using nrf51442 as central client.
I have used
SDK\v7.1.0\examples\ble_central\ble_app_hrs_c\pca10028\s120\arm\ble_app_hrs_c_s120_pca10028.uvproj" as a atart point...
