At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
I need a fixed voltage reference on my circuit. Since nRF51822 has internal 1.2V voltage reference, I am just wondering if there is a way to use this reference for external...
Header for nRF51 (nrf51.h) mentions two peripheral blocks completely missing from chip documentation. Are they functioning? If so, the comment for PATCHADDR field of PU says...
Hi there,
After prototyping a device with modules and on a breadboard, I transitioned to a custom PCB with nRF24L01+, matching network from the spec sheet, and 2.45 GHz...
Hi everyone
now i used softdevice s120 scan and connect two s110 device
and i used sd_ble_gap_rssi_start() when connect event ,
then get the rssi in BLE_GAP_EVT_RSSI_CHANGED...
HI,all!
Recently my nrf51822 device encountered a tough issue,the detials are:
My device connected to an android app, which has some bugs about ble connection so the...
HI,
I am using sdk 8 and pca10028 dk. I follow following procedure,
Program the softdevice using nrfgo
Program the test_bootloader using nrfgo
Program the application...
I have some questions about how I will use this structure ,first of all I know that The "data" member of the ble_gatts_evt_write_t is meant as a placeholder for the address...
I am trying to create a windows app that will read data from an accerometer via a nrF8001 ble module.are there any example i can see for communication between windows and...
Hi, Nordic Engineers. Now, i use a external 32mhz crystal on my board. i have add code"NRF_CLCOK->XTALFREQ = 0X00", but the BLE radio seems not work. Led flick is ok.
Why...
Hi Guys,
I have a SITECOM Bluetooth Dongle connected to my PC and I want to receive data from nRF51 DK via bluetooth (for example heart rate monitor data).
Could someone...
Hi everyone,
I must to comunicate from HW to PC with SPP over BLE. So I took the dongle BLED112 (side PC) and the HW where is mounted a nrf51822 like uart BLE interface....
Hi,
the product specification of the nRF51822 states the possibility to carry quadrature demodulator
signals on GPIO pins.
This would let one allow to observe the physical...
Hi,
I am a newbie to nrf, I am trying to understand the lbs example while running on nrf dev board. I want to set my application as follows:
Blinking LED while advertising...
