We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hello, I have tried to combine saadc with softdevice, but having errors during compiling. I have copied .c and .h files from saadc example to ble_hrs example, but having following...
Hi,
I have a specific application/product where in I am planning to use Nordic nRF52832.
-> There is a 9 Axis Inertial Measurement Unit (accel/gyro/magnetometer) connected...
Hi!
I have been trying for over a year to figure this out, but I am unable to, and I would hope it be pretty straight forward since OTA is already in the Nordit Master Control...
FIXED (see below)
Hi!
I'm developing software for nRF52 on nRF52 preview DK, which I got on the Global Tech Tour.
LED blinking (blinky) example is running OK, so I moved...
I have a device (configured as a slave) which is connected to a relay to on/off a motor.
Now, I need to connect it to multiple masters (e.g., couple of smartphones) to remotely...
Hello Guys,
I need suggestion regarding the selection of nrf8001 ble module
Does it support OTA updates?
What is communication interface? is it SPI or conventional...
Hi,
I want to discovery all attribute UUIDs as Master Control panel application does. I use API function 'sd_ble_gattc_primary_services_discover' to discovery.
Exactly...
Hi:
I develop my project with gazell, Device can keep send to host,but host can't keep send to device(I'm not mean for host sent ack to device).
In my program, I use "nrf_gzll_add_packet_to_tx_fifo...
In the nRF52 reference design, not using the DC-DC converter would result in higher power consumption. By how much? Any documentation regarding the details. Thanks
Hi all,
I am new in nRF51822. Today I am doing experiment using GPIO and radio transmission.
I wrote a very simple code as below:
int main(void)
{
init_clock();...
Hi, I've got a serious problem in my project. Some of its features require hard timings. The usage time of these features is longer than the single timeslot and I must be...
Hello guys, I'm doing a hobby project and can't seem to get it working. Aim of the project is to transmit temperature values from a DS18B20 using an Arduino Uno and NRF24l01...
I'm experimenting problems with a nRF51822 custom board. Recently I managed to run the blinky sample project. Now I'm trying to test a BLE project, but I'm having problems...
Hey All,
I am currently trying to have a Analog Signal come in through P0.05 which then gets converted via the onboard ADC and send out a Service Characteristic. I am using...
