Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Dear sirs,
Many thanks for the IoT SDK.
Just setting up the Raspberry I can't start the Phyton CoAP example as defined in documentation.
The envirinment is:
R...
Hello everybody,
I'm getting crazy, I'm trying to extend HID axis values from 0..255 to 0..1023 max using the descriptor found in the example ble_HID_keboard/hid_joystick...
Hi All,
I am struggling getting my N548 module to transmit any ANT+ ...
I have tried the Cycling Power Sample Application (S310)
And the Cadense / Speed (S210) Sample...
Hello,
Is there any delay between when the reset pin is driven low and the actual reset of the chip. Would it be possible to sense the reset pin and perform some quick...
I am designing an nrf52 based device running at 1.8V. To debug the device I was planning to use debug out option of the nrf52 preview DK. However, I just find that, the debug...
I'm trying to follow the code from one of your examples, specifically ble_beacon in SDK 8.0 and eventually I get to a point where I'm not sure what's going on so I figured...
Hello,
I have question. I using examples with nRF51-ble-peripheral-bond-handling with bls_service (PCA10028) and i have problem with unnecessary connection. I want that my...
I'm referring this blog on getting started with nRF51822 and in this same blog, there is a link to a video by Nordic on Introduction to Bluetooth Smart and after watching...
I have two STM8s105 MCUs and two NRF24L01+ modules. Set one as transmitter:
CONFIG: 0x3A
EN_AA: 0x00
EN_RXADDR: 0x03
SETUP_AW: 0x03
SETUP_RETR: 0x00
RF_CH: 0x00...
Hi
I used the boot loader example successfully on the nrf51DK board.
Now I want to use it on my custom board. So I recompiled the boot loader code, with 1 difference:...
I don’t fully understand the nRF51 event NRF_RADIO->END. NRF_RADIO->END identifies the completion of a packet transmission or reception. My question is what triggers NRF_RADIO...
We have a project that involves both battery-powered 'slave' devices and a mains-powered 'master' device (which needs to support multiple slaves and support WiFi). We are...
Hi,
imagine that I have a proprietary characteristic that allows only READ operation (from a smartphone for example) that expose an internal value in my application.
I...
Hi,
I'm using nrf51822 and SDK 6.1.
devzone.nordicsemi.com/.../
I learned how to store data with using pstorage library.
but I can't register block more than 1024...
my chip : NRF51822 (256kb)
SDK : 6.1
Hi.
devzone.nordicsemi.com/.../
according to this example code, I could have stored data and it works great.
but problem...
I want to update the bootloader inside nRF51422 using iPhone.
Updating applications hasn't been any problem.
Following the same procedure but I cannot convert bootloader...
