I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
Hi,
Recently,
the DFU of the "Master Control Panel" (Android) can not complete the upload mission.
But,
the DFU of the nRF-Toolbox in iOS is
work well.
Old...
I just tried out the new iOS nRF Toolbox 1.5 and it doesn't seem to handle long init packets.
I gave it a zip file that contains a 137216 byte 'application.bin' and a 192...
Hello everybody,
In the SD_EVT_IRQn ISR I check for BLE and SoC events and set flags for each so my application can fetch and dispatch the events in the main context. ...
Hi, in the example bootloader in sdk 7.2, there is an assembly code block in SVC_Handler, in dfu_ble_svc.c.
I found that the offset in line:
LDR R0, [R1, #24]
always...
In nRF51 SDK 7.1.0, there is a c header file using c++ keywords operator .
Here is a snippet of components/ble/ble_racp/ble_racp.h using the keywords.
/**@brief Record...
Hello,
i want to write a global unsigned long variable in RAM after programming the device. The Use-Case is to set the clock value to the actual time. So the new unsigned...
I use BLE mesh github.com/.../nRF51-ble-bcast-mesh
but when I use the master control to write values to update the values of services, the following error occurs: "global...
Hi. All.
I am in the process of update SDK 9.0 from 5.2.
Meanwhile, SPI couldn't read from external flash's data.
Unusually SPI works well before infinite loop, I tested...
Hi there is a problem in github.com/.../nrf51-UART-examples
any one can help?
I put empty loop in main, and comment off all ble related int. and I process uart_evt by...
I want to use the nRF51-DK board as a programmer for my target. As I understand it, this can be done with the signals on P19. However, there is one signal, EXT_RESET, that...
github.com/.../nrf51-UART-examples
Hey any I was trying to test the example, the one with BLE
I test
APP BLE sending --------shows on PC UART software
However, I can...
Hi,
I would like to ask if someone has experience using the AES. I n eed to be absolutely sure that the user SW can use the AES HW block for own custom usage. If yes, Are...
I'm using SDK's interface for AES ECB block, but getting a hard fault when ECBDATAPTR is redirected at ecb_data in the initialisation function:
static uint8_t ecb_data...
I have built the dfu_dual_bank_ble_s110_pca10028 project and attempted to load the ble_app_hrs_s110with_dfu_pca10028 application. I did find that if the use the S130 softdevice...
Hello,
I have a nrf51822 chip using s110 SD. I am trying to read a serie of 14 bytes from UART. If the device is connected to a phone with BLE I receive the correct values...
When my nRF51 DK is only a board without any software.How can I make it work and support for mbed?
If I have to flash the SoftDevice, the bootloader by using nRFgo Studio...
Hi All,
Am developing an app that communicates with an embedded device through Bluetooth low energy.
The embedded device is sending the data in hex format say "35AE51BA44...
Does sample code exist for the pstorage module?
I am calling this code right before advertising_start() in the heart rate monitor application for the newest SDK. It doesn...
