I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
I am considering using a high-Q BAW filter to drive as near the band edges as possible and roll-off noise beyond.
Source of my interest:
https://www.qorvo.com/design-hub...
I am using nrf52832 SDK14.2 development, now the system will generate some strange exceptions, I am worried about the stack overflow, is there any way to confirm whether the...
Hi All
We are using nRF9160DK and want to send data to the cloud (Adafruit or Thingspeak) using MQTT protocol but we do not have NB-IoT
Network in Our area so it's possible...
To the kind attention of Nordic support team,
I've been reading in this post:
https://devzone.nordicsemi.com/f/nordic-q-a/44042/using-nrf52810-with-gzll_nrf52_arm-lib...
Hello,
I need to validate my selection for crystals working with the NRF52840. For the 32.765kHz crystal I have chosen the 9HT12-32.768KBZC-T from TXC Corporation. For the...
i have test with RTC using nrf_calender.c.
It will prints output data on terminal window.
But, I didn't recognize the actual data.
Output data is mentioned below,
...
I am attempting to use libmbedcrypto.a from the Thread/Zigbee SDK version 3.2.0. I am linking it from:
external/openthread/lib/nrf52840/gcc/libmbedcrypto.a
and yet...
HI,
I want to implement the software security to NRF52832 such a that no one should be able to read the memory or tap the data during Bluetooth communication.
Regards...
Hi,
I am trying to interface tlv493d with nrf52 dev board.
I have taken driver code from infeneon
https://www.infineon.com/cms/en/product/evaluation-boards/tlv493d-a1b6...
Hi
I face ble disconnection issue.
we use external crystal 32.768khz. However, when I check it , the load cap is wrong. It should be about 9pF but it is 1pf.
The frequency...
Hi,
When factory resetting the flash storage, I delete all records, and then call fds_gc(). However, the page that's used for garbage collection still contains a copy of...
Invitation : The provisioner invites the unprovisioned device to send its provisioning capabilities information.
Firmware version from this examle: https://github.com...
Hi.
I've bought the nRF52833 DK and I want to use it with Mbed OS.
But I'm not getting it to work. If I compile the "mbed-os-example-blinky" program for target nRF52-DK...
Hello.
I would like to ask about writing data from Smartphone to Thingy. How to change characteristic using setOnCheckedChangeListener.
Is it correct way to change characteristics...
