Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
Hi there, I am developing a mobile solution using BLE. Actually I use a sniffer based in IC nRF51822 and Wireshark + nrf sniffer as a tool for traffic capture. Sometimes,...
Hi,
I have similar problem to what is described here .
My situation: 1. I connect 2 PDM mics to the board (CLK is pin 27, Din is pin 26). 2. I connect a couple of TWI...
I was wondering if there is any way to setup a callback when data is received on an open socket, as opposed to just regularly polling the socket?
The application I have...
Assume a BLE connection has been established between a master and slave. The device in question could be either the master or the slave (if it matters).
I have an application...
Hi, when using fds_record_iterate() to iterate over records, it only returns the record ID, but not file ID or record key. Only after opening the record you get the file id...
The nRF52810 datasheet shows the EVENTS_COMPARE register as RW, so I'm assuming that I can write to it.
But when I write to it, nothing happens.
Example.
I set up...
The question in short form is, is there any way to not use the Flash for storing bonding information and instead do this in RAM?
For the longer explanation:
We are using...
Hi,
We've circled back to this problem, now that we've increased speed.
We're using UART to communicate between the nRF52832 and an STM32.
Recently we increased the...
Hi,
I am trying to read UART data which is populated from another device going into the nordic board.
However, I am unable to read this data. I am using the ble_app_beacon...
Hi,
We are running a setup that pumps sensor data from light switch server to light switch client. After provisioning/configuration the setup is working fine without any...
Hi all,
I am try to test light switch server example in mesh SDK (v3.2.0) with nRF5 SDKs(v15.3.0). Using Coded PHY(125kbps) as this post or standard PHY (1Mbps) seperately...
Hi Devzone!
I'm using the fft function to check the frequency of sound from mic sensor.
All seems good but, o nly up to 2500hz is shown and the frequency above it is...
Hello,
I am trying to measure the battery voltage on an nRF52840 DK using SDK 15.3, while consuming as little power as possible, so by using nrfx_saadc_sample_convert()...
The example initializes the SAADC driver and configures one channel to sample analog input 0 (GPIO pin 2).
I would like to know how to change analog input pin to other GPIOs...
I'm working on nRF52840 SDKV15.3.0 SoftDevice S140. When setting 2mbps mode and long range mode getting <error> app: Fatal error .
i'm using xenon iot development kit its...
