We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
I am using nRF52832 DK.
I am trying to print Battery service value in log file ( Client side ).
So where i get this information and how can i print this information in...
I’m looking for setting up an evaluation network considering of 10-14 nodes as data sources that are to send data values on a periodical basis to a data sink mode that will...
Hi everyone,
I am developing application on nRF52832 using SDK 15.3 on SES, windows. I am using secure DFU bootloader for FOTA process.
Scenario 1 : If I don't use DFU...
Hi Team,
After I add the ANT module into my project, I found the fds_gc() will always return error 1( NRF_ERROR_TIMEOUT ) when it has dirty records. If there are no dirty...
Hi,
I am using NRF51822 SDK12; S130 and trying to qualify Batter level service, So far encountred a problem with Test Case: BAS/SR/DES/BV-02-C, the Verdict is INCONCE all...
Hello, I just got the nRF52832 development board and i was playing around with the examples. I was able to connect it with the nRF Connect app on my mobile and desktop. But...
Central info SDK: 15.3 nRF52840
Peripheral info SDK: 13.1 nRF52832
I want to increase the communication speed after connection. I want to know how to set the communication...
Hi,
I'm trying to measure the power consumption of the nRF52840 chip , which runs the "nimble" BLE stack rather than SoftDevice.
However, the nimble BLE stack runs on...
Dear Nordic Team,
We want to use the FreeRTOS for commercial use, kindly request to answer the below questions.
1. Is AWS FreeRTOS open source & commercially distributed...
Hey all, I'm a beginner to bluetooth,
I ordered the NRF51822 dev kit and it worked easily out of box with my android phone.
I'm creating my own android app to communicate...
Hi Nordic
I want to change mesh-sdk-4.0 LPN example tx output power to 4dbm, including proxy broadcast, mesh packet,
I try to change " RADIO_POWER_NRF_0DBM " in whole...
The Nordic Uart service for peripheral devices has a function ble_nus_init() which takes a callback function in a struct.. Later on this callback function may be called with...
I am doing the project using nrf blinky.
My phone cannot find the nrf52840 . Before this it is ok, but now it cannot discover it . I notice that LED05 is blinking very fast...
