Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hi,
I'm using SDK v3.2 and I'm extending the lighting example. I'm developing an extension to the provisioner, to inform a back-end about the configuration of the subnet...
Hi,
our device has current limitations in the range of 1mA. We were examining several ways to limit the actual connection parameters to keep current consumption low. But...
Hi,
I'm developing an application to monitor the current application and network context, by extending upon the existing Light Switch example in nRF5 for Mesh SDK v3.2.0...
Hi everyone !
I have 3 services and 13 characteristics in my project. Until today, 3 characteristics were working fine. But i added rest of the characteristics and my project...
Hi all,
I am currently using Pyaci serial to establish and test BLE mesh network, and it work fine.
The further step we want to do is to create a duplicated Provisioner...
I have a Thingy52, but no DK. I would like to know if it is today possible to upload a custom firmware only using OTA (no DK), eventually starting from the Nordic Thingy app...
Hi,
I'm trying to transfer data between an nRF52840-DK and an Android phone which has nRF Connect installed on it and I can only reach about 40kbps (that is kilo bytes per...
Hi, I am working on installing the pc-ble-driver-py library and building it to run an application for a nrf52840 Dongle over serial port.
I have followed github.com/......
Hi everyone!
I have a nRF52840 dongle and I am trying to run python examples from pc-ble-driver-py. The dongle is connected to a PC running Ubuntu 18.04. The dongle is flashed...
Hi,
I am using the SDK 11 on nrf51822 I just merged the TWI sensor example and the BLE UART example. Both work together but the softdevice seems to be slowing down the twi...
Did anyone configure correctly VS Code with nRF Mesh example?
I did install CMake on my computer and download CMake extension to VSCode. I am working on Windows.
I did...
Environment - Mac - nrf tag; 1.1.0 - modem fw: 1.1.0 - DK 0.8.5 - debugging by SEGGER RTT The program polls SMS for a certain time and if SMS is received, it reads the messages...
Hi.
I am trying to update soft_device version 6.0.0 to 7.0.1.
I read that because of the major version change (from 6 to 7), i must update the bootloader as well.
I...
Hi,
I am prototyping with the the THINGY52 using nRF Connect.
I am using the services available to drive the MOSFETs on the expansion connector P4 through the services...
Hi,
I would like to debug the code which is in Nordic Thingy91 by using nRF52840DK.
Is it possible to use the debugger in nRF52840DK for Nordic Thingy91 ?
If it is possible...
