after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Hello,
I'm started implementing DFU over serial port and see documentation from this link: https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.sdk5...
Hi, I am now using nRF24lu1p, for using cklf_wdog_init() to enable watchdog, then I set cklf_wdog_init(10) in main function, but don't know how to set watchdog event handle...
So we have been developing on the nRF52811 and realized we need OTA (Over the air Frimware) aswell and we have 30kB Flash and 8kB Ram remaining. Can this be done?
Also a...
Dear Sir/Madam,
I am trying following,
1. Avoiding SPIM transfer interrupt handler.
I am performing following steps,
1. nrf_drv_spi_init() for Handler parmater 'NULL...
Hello,
I'm using nRF connect for power profiling of nRF52840 DK. First time it works.
If we close the nRF connect and open it again then I get error.(Also after power...
How can I do LESC on my central with an Android peripheral device, if with each new connection the MAC address on Andriod changed randomly?
The first time I am making a...
Hello,
I want to use 100 bytes of flash as non-volatile data memory. We should be able to read and write this memory during execution.
So for this purpose I need the implementation...
I already follow the link for terminal in this link https://infocenter.nordicsemi.com/index.jsp?topic=%2Fsdk_nrf5_v16.0.0%2Flib_cli.html&cp=6_1_3_10_3&anchor=lib_cli_terminal_settings...
nRF52DK
p20 debug out
external board is 51822 + sensors
I managed to connect the external board through p20 on the 52DK. I can successfully program the external board...
I am reading about nRF52811 SoC which is currently supported by nRF5 SDK v15.3.0 and SoftDevice S112.
I want to know more about its direction finding capabilities and play...
Hi,
I'm trying to add the NUS service to an existing application (freertos based, SDK15.2, already use a custom service)
I copied the relevant code snippets from...
Hi everyone,
I'm trying to use nRF52810 with SoftDevice S112 to sample five ADC channels. I'm finding this very weird issue, where first channel is showing correct value...
Just getting started with Nordic toolchain and I got this error below.
=== updating civetweb (modules\lib\civetweb): --- civetweb: cloning and initializing Initialized...
i need a code for when button press after one second delay led will glow continiously whenever again pressing the switch it will stop glowing using apptimer
