Hi everyone,
I'm working on a project using the Nordic nRF5340 microcontroller and I need to count both rising and falling edges of a square wave signal on pin P0. 14, coming...
Hello, I’m working with a combination of nRF5340 + nRF7002 + NPM1300 , and I’ve only changed the I2C pins connected to the NPM1300 to sda pgio1.4 and scl gpio1.6 .
SDK...
I am running into a secure fault when I set the NVS_SECTOR_COUNT to >= 7, not sure how to proceed.
it fails at nvs_mount(&fs)
I have added a nvs_storage partitation...
I've seen other threads about the issue:
- https://devzone.nordicsemi.com/f/nordic-q-a/117267/light-bulb-sample-works-on-nrf52840dk-and-doesn-t-on-nrf52840-dongle
- https...
Here is my script for programming. Does the sequence is OK? or any advice to improve?
nrfjprog --eraseall
nrfjprog --recover --family NRF53 --coprocessor CP_APPLICATION...
Using the peripheral_uart example routine from the NCSv3.0 library with the 54l15 chip.
1. compilation command: west build --build-dir build . --pristine --board nrf54l15dk...
I'm looking into a rare issue on the BBC micro:bit V2 which uses the nRF52833 as its (application) microcontroller. I used to be familiar with some CPUs from the 80s but my...
Hello All,
Recently, I started working with nrf9160 and found it uses Zephyr for building application. Can anyone suggest me a any good tutorials for learning Zephyr from...
Hi I am following the instruction in the following link to do a open DFU through USB UART:
https://devzone.nordicsemi.com/nordic/nordic-blog/b/blog/posts/getting-started...
We're experiencing occasional unexpected hardware watchdog resets. The watchdog is set to 10 minutes, and sometimes just 2 minutes after feeding the WDT we see a reset triggered...
Hi there,
I'm currently developing a ble mesh network for the Thingy 52. I'm accesing the temperature and humidity sensor but I need the firmware code of the Thingy 52...
Having problems bootloading my own application on my hardware. The application runs fine alone. Using SDK 16.0 and secure_bootloader/pca10056_uart example via Segger SES....
Hello,
anyone with with knowledge on how to control the gpio pins of the NRF 9160 SiP?
In my scenario, I am using P0.01 - P0.12 as digital control signals, for "Enableing...
Hi Nordic
For mesh-sdk-4.0 examples/light_switch/server, how many LPN can a server to establish friendship?
Is it limited to MESH_FRIEND_FRIENDSHIP_COUNT?
Regards...
Hi, I have custom nRF52832QFAAE1 when I tried to run Peripheral applications which are working fine. whereas BLE applications are not running it seems.
here are the things...
Hello,
When I clean a project and do a new build, parallel settings looks wring (my AMD ryzen 3900X with 12 cores never use more than 40 %).
Do someone have a setting...
Currently, we are testing the nRF52840 range evaluation using the nRF52840 EVK kit.
As of now, we are getting the only 120 to 125-meter range using 125kbps data rate @ 4dBM...
Hello.
I found in Provisioing chapter on this document: https://www.bluetooth.com/specifications/mesh-specifications/
something like list of provisioning commands: ...
Hello.
I plan to perform antenna matching to improve the performance of my design.
I would like to know any differences when performing the match on bare pcb and pcb...
Hi,
I'm working on a test for the pulse width measurement, the input is analog signal.
I'm using a while loop, and use nrfx_comp_sample in the loop to get the voltage...
Hi All,
I just start to use the Thingy 52 and I would like to know if there is any source code for development purpose for Windows. Also, which development software does...