We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hello,
i have read all posts about writing to FLASH when using BLE. But could not find the desirable method.
What i would like to do is to write to flash from characteristic...
I'm trying to add the product key it shows an error "can not the product to your list" and therefore i will not able to access to the User guide
Thank you
nRF52840. In case of standby current (battery only)
Measured as follows:
With only the battery connected, the same current draw as the one attached. Is there any...
In my DFU bootloader I am protecting areas of Flash memory used to store user data.
After an update, when my application starts and tries to write to this memory it is causing...
I am trying to use the real time clock on the nRF52840 dongle using the pc-ble-driver. However, my nrf.h file has nothing in it but the following:
#ifndef NRF_H__ #define...
I have a working iBeacon advertising a beacon UUID, Major, & Minor on a nRF52832. In addition, I also have a single BLE service (which has a single characteristic) defined...
Hi I am managing to initialize a serial instance using uart0 within the BLE Buttonless DFU Template. However when I carry out a similar process for uart1 I get the following...
Team,
I received the following customer inquiry and hope you can help:
The BLE – WiFi bridge project I’m working on will need to control up to 64 nodes, not concurrently...
Hello,
I am trying to upload the firmware with secure DFU using following method:
generated the dfu_public_key.c and private.pem pair
copied the " dfu_public_key.c...
Hi Dear Team,
I am using the nRF52840-Dongle and pc-ble-driver-py-0.12.0 for the ble development, while I encounter a problem about the max connection per device.
I use...
Hi,
I've got some questions about setting up a connection.
I want to connect as fast as possible with a UUID filter. Is it possible to connect directly on the first advertising...
How to set 250kbps PHY Coded in NRF52832 BLE Mesh? I have tried to change scanner_config_radio_mode_set(RADIO_MODE_BLE_1MBIT); to scanner_config_radio_mode_set(RADIO_MODE_NRF_250KBIT...
Hai ,
I need to update nrf52840 over ble from esp32 . first i tried with app , firmware gets updated .. as per the dfu protocol i understood flow and tried to writing data...
I need atleast 10 UART channels to be configured in my project. Is it possible to do it with the NRF52840. I believe because of the PPI I should be able to do this. I was...
I want to create a small bluetooth device with the nrf52823 chip. I want to use a lithium battery cell to power the whole circuit and therefore it neet to be low power. On...
I'm bigger of NRF52832 and beacon concept. I need modify my beacon data like Major,minor and Tx power change via mobile app configurable. please share any example code or...
