I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
It is good practice to prefix the includes from one's C libraries with a directory so that they are all part of the same 'include namespace'. Unfortunately the Nordic SDK...
Hello,
I have two micro-controllers communicating over SPI.
The STM32F746 is SPI master. The nRF52840 is SPI slave. I use SDK v15.3.
I am sending two bytes over SPI...
Hi.
I had to unpair from the Android Bluetooth list by doing pm_peers_delete () when bonding. It's ok. I know why it should. But sometimes I can't find my paired device...
To the kind attention of Nordic support team,
We are very interested indeed in using your nRF52840 and nRF52810 devices in our projects. We also would like to use your gazell...
Hi,
I have used nRF52832 with my Python code succesfully many days. Suddenly it stopped to working and gives me an error message: NordicSemiException: Failed to ble_gap_scan_start...
Hellou. I'm developing application, which is modifiaction of light switch demo. I need use 128 servers and one client. But when I redefine in SERVER_COUNT to 128 in client...
Hi all, ( nRF52 DK, SDK 15.3, S132 )
Many asking about how to add 2 "service data" in the GAP advertising, but no real answer on the solution !
The first service data...
Hey everybody!
I'm trying to implement the following use case.
Android device connects to nRF52, bonding occurs, android device is put into nRF52 whitelist, after this...
Hello, I am trying to combine light switch client example with fds functionality.
For these I did next steps:
Included all ‘c’ files from the fds example to the light...
I notice that the USB Serial (the lowest numbered COM port of the three, that's connected to the Cortex-M33) isn't opened in a Serial Terminal before the application starts...
Hello:
When I try to use mesh, I found that the bootloader never work in low power mode. If I only program application into the nrf52832, the power consumption of its low...
Hello.
I m working with mesh demo: https://github.com/NordicPlayground/thingy52-mesh-provisioning-demo
In Android app we can press "identify" and after that Thingy's led...
Hi, On a button press I need to enter to disconnect from the currently connected device and then start advertising in order to allow a new device to connect. I manage to disconnect...
I am trying to read analog value from a GPIO pin. Particularly I want to read battery voltage from a GPIO pin assign to P0.31. Please help me how can I read the analog va...
Dear All,
Thanks for your continued support.
I have been trying to get debug terminal to work... I enabled RTT log and disabled UArt in the sdk_config file. I set...
