Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hi All,
I'm developing my product based on nrf51822.
I was using keil IDE for that.but i wanted to develop it in Segger instead keil ide.
is segger is supporting for...
Hello, I am working on an IoT project. For this project , I need to send some data using BLE. I developed a firmware for this application based on the sample ncs/zephyr/samples...
HI ,
In our project we are using multiple gpiote and app timer interrupt.
SDK we are using is 15.3
DOUBTS
If both gpiote and app timer interrupt trigger simultaneously...
Hi,
I'm using nRF mesh library v1.2.1 and integrating into my mobile application which I am developing, I implemented provision functionality without errors but sometimes...
I am bringing up a custom board based on the PCA10040.
As the first step, I simply copied (no changes) the file pca10040.h and named it as "my_custom.h". I then defined...
We have an nRF52 DK system running ble_app_uart_c example code and communicating with a peripheral device. We setup a second development system using another nRF52 DK system...
I have the nRF52840-DK with the adafruit PN532 RFID/NFC shield installed on top of it.
I run the TWI Scanner and receive a report that a device was found at address 0x24...
I am having a strange issue with my custom radio protocol. I have ported the code to the 52840 and SDK15 from the nrf51822 where it is running with no issues.
The issue...
Hello,
I have PCA10040 development board with nRF52832, Softdevice S132 v6.1.0 & SDK 15.1.0). I wanted to use the extended advertisement feature to advertise more than 255...
Hi,
After developing two application, one for emitting extended advertising and other one for scanning this kind of advertising on nRF52840 DK (Github repository here: MOTAM...
Hi,
I would like to ask two questions.
1)
I understand that the nrf52832 does not support the feature "Transmitter has a Stable Modulation Index".
But the component...
Hello, I am trying to build the asset tracker reference app for my newly acquired Thingy:91.
I went through the instructions to get the toolchain and SEGGER IDE up and...
Hello,
We are currently using a Raytac SoM that has nRF51822 SoC with Adafruit UART firmware. We are running into two different scenarios BLE connectivity issues where the...
While going though the Makefile of the FreeRTOS HRS example in SDK 16.0.0, I noticed this part:
By default, link time optimization (LTO) is not enabled.
If I enable...
