hello, Nrf24LU (Rx) , nRF51822(Tx).
The Nrf24LU Can only receive one packet。
if I use this function twice ， like this：
The Nrf24LU can receive Continuous.
I guess The...
Hi,
I use SDK v10, S110 v8 and dfu_dual_bank_ble_s100_pca10028. My application has dfu support.
I reset to bootloader from application after writing 0x0104 to dfu control...
I have a nRF51822 device.
When the connection interval is 50ms.
The transmission distance can up to 50m+.
But, when the connection interval is 1000ms.
The transmission...
Hi,
I have a simple question. It is possible to use the ble-sniffer nrf51822 on Kali Linux? I found a guide to use it on linux but I don't know if it is the same for Kali...
I've modified Nordic's "Nordic_Keyboard" sample to work with my custom board, just simple modifications to use custom_board.h rather than the default PC10028 configuration...
Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
Hi,
Is the Errata 15 applicable to Softdevice?
Does Softdevice at any point read the RAM state using RAM[x].POWERSET and RAM[x].POWERCLR registers?
Thanks,
Just...
Hi Now I'm developing using nRF52832, and trying to estimate programming time.
So, I want to know what time to wrie one word "tWRITE" mean exactly. Does it mean that one...
Hello, I am currently building a wireless sensor network, and I am searching for a transceiver and not a complete system on chip. I was working using NRF24L01, and now is...
I tried to write in flash since a couple of weeks.. and i am not able to do it... I am using SoftDevice... so i think i have to use Persistent Storage Manager Where can i...
Hi Devzone:
I am using the example project "fsorage" on nRF52840.
I see the project specifies the range for the flash storage to be
.start_addr = 0x3e000, .end_addr...
Hello
I am preparing for Bluetooth SIG certification. I use nRF52810 / SDK15.0.0 / S112 6.0.0.
I've been helped by Nordic about QDID before.
https://devzone.nordicsemi...
Hi there
After initializing the SoftDevice S132 V6.1.0, I request the HF crystal by calling the function sd_clock_hfclk_request():
Later in the code, after a BLE connection...
SDK:V16.0.0
chip:52832
development kit:window+keil
I trying to combine libuarte and ble_central\ble_app_multilink_central\. My project work well in ble_central. But...
Hello everyone, I need to build a photo capture application.
And the CMOS sensor go through MIPI-CSI2 interface.
Is there any example code and library for nRF5340?
Hi,
How should the USB pins be handled in case I don´t want to use them? Should they be just left unconnected?
What about VBUS pin?
Thanks and regards,
Juan
Hello,
I got the issue to run the NRF9160 DK as an external AT-Modem. What I need to do is to issue AT-Commands over the UART, which control the NRF9160 modem through an...
Hi , I am running zigbee cli example code from sdk and configuring nrf52840 board as coordinator and trying to add xbee module to zigbee network. Coordinator is not accepting...
OK, a bit of confusion somebody can clear up for me, I hope;
Does NRF_SERIAL_EVENT_RX_DATA get sent when there is ANY data in the RX buffer, or only when the RX buffer is...
