Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I am running Windows 7 Pro SP 1 64 bit and have gong through the tools installation procedure, in particular running nRFTools_7_7_0_Installer.exe. This ran the J-Link V5.02...
Hi all,
I am working with SDK 15.3 (S140 6.10) on ISP1807, which is nRF52840 based.
For my application I needed a USB dongle which works as BLE Central. It is supposed...
Hi all:
Currently, when using nRF52840 for archiving applications, I will encounter a condition and this will result in data corruption.
And I found a way to reproduce...
Hello,
I'm having a bit of difficulty disabling the PWM peripheral when it is no longer required. From the manual it states that "To completely stop the PWM generation and...
I have a custom BMD-350 board with a UART service. The board connects just fine with the nRF Toolbox iOS app but does not work with the Android app. The app connects to the...
Hi,
I am a little bit confused about the different supported stack for the nRF52833 when using BLE Mesh. With the current example, there is only support for the S113. Can...
I started a timer on the nrf52840 and the SDK is nRF5_SDK_15.2.0_9412b96, but I haven't never receive the callback message after the time. What's the reason?The code is as...
Hello ,
In this scenario, I have to measure the time interval between the START and STOP pulses generated by a peripheral device connected to nRF52 DK. The thing is START...
Hello!
I am currently using a module called BLENano2 (nRF52832). SDK15.0.0 is used and the editor is "Segger Embedded Studio v4.16".
Finished writing the program that...
Hi,
I tried out the light switch example on a nRF52833 and it seems not to be reliable at all. So i connected the debugger and saw, that in access.c,
in packet_alloc_and_tx...
Hi all,
I am trying to use nrf52840 dongle as hci_usb with the very simple task: scan
Host is Raspberry Pi with BlueZ
Controller is nrf52840 dongle with firmware hci_usb...
Hi
I want to move DFU at the application level. Is this possible? I want to move DFU at the application level because of my project requirement.
1. In my project, I have...
Hi, I am trying to get the BLE values on Thingy91 (PCA20035) . And I have followed the
devzone.nordicsemi.com/.../217018 I have ported the diff (nrf and zephyr diffs from...
I am using built-in DTLS for encrypting my UDP traffic. In order to save expensive data quota and reduce battery drain, I have to make use of session resumption, so that I...
Hi. I have a question about Bluetooth 5.1. I just want to know what the main difference is between a Bluetooth 5.0 and Bluetooth 5.1 chip.
Is it the hardware or software...
