Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
Hi,
I am new to the SAADC concept in nrf52. I have to measure the battery voltage using SAADC over ANI0 pin. I using battery with voltage 4.1 volt.
This voltage is divided...
Hi nordic,
In our project we are using pairing and bonding process. the first pairing with the iphone was successful, I delete the NRF52832 pairing infomation,iphone pairing...
Hello ...
Our product (nRF52810, SDK 15.3.0, SD 112 6.1.1) allows the user to change the device name, which typically happens once when new product is received. Our app...
I am running the ADC demo for the 52833-DK (pca10100) and can’t seem to get any valid readings. SDK 16.0: examples\peripheral\saadc
I am applying 1.5V to AIN0 on P8 and...
Hi, I am developing something using Zephyr on a nRF52840-DK as one Bluetooth mesh node and a Thingy as the other. To program the Thingy, I have it connected the Thingy to...
Hello -
I am trying to run the USB CDC ACM example on macOS 10.12.6. Following the instructions in the example app, I should see a virtual COM port as /dev/ttyACMx when...
Hello,
I am doing some testing on the nrf52832 DK using the mesh light switch example, i am sending ACK messages, i would like to log the time it takes the message to reach...
Hi,
What is the proper way to set "real time" in nRF9160 with nRF Connect SDK?
I want the function time() from the file time.h to return the correct time.
I know that...
I am using SDK15.3.0 and softdevice 6.1.1 on a nrf52DK.
I have a binary (compiled contiki application) that works when I flash it using nRF Connect. It is flashed from address...
Hi,
I have a PCA10040 board (nRF52-DK) which has a P20 debug out interface. I've got another nRF52832 breakout board which has VCC/SWIO/SWCLK/GND wires for debug/programming...
Hey,
I configured one device as low power node in mesh network.
With the button press interrupt low power node wakes up and perform some operation (publish BLE message...
Dear Nordic
I am using SDK14.2, I cannot pint info . SDK periphral uart and serial can't print also
nus example jlinkrtt print as below:
<00> warning> nrf_sdh_ble: RAM...
Hi,
I am using pc-ble-driver version 4.1.1 with the SD version 6.1.1.
I want to configure the TX power for the NRF52 USB dongle.
Do you have a code example for configuring...
Now I can build & download nRF52840 SDK example with Eclipse.
But Eclipse indexer(F3 key) can not recognize include folder.
So I added every include folder to .cproject...
I'm having a advertising device and then I want to stop advertising and prevent BLE connection from device that would have received the advertisement. It seems to work by...
