Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
Hi there,
I want to use a LiFePO4 Cell to supply the nRF9160:
Is the MAX17224 suitable to power the nRF9160?
Is this Power "Sequence" OK? Productspecification nRF9160...
currently we are facing an issue with our testing that, our product battery is getting drained to 0 volts. we understand that we need to put a cutoff voltage from the firmware...
Hey folks,
I'm developing a long-range application with nRF52840 DK that (optionally) uses NUS (Nordic UART Service) to send data to Samsung S10+; there is no problem establishing...
Hello,
SDK 15.3.0
nRF52840-DK
s140
IDE:SES
I am running into an issue using the app timer and LPComp together. The error is NRF_FAULT_ID_SDK_ERROR, With RTT output...
Let say during the normal program flow I want to change often the edge direction which will trigger the event: rising edge, none, falling edge, none … Can I work direct with...
hi:
i want to know CKCON config is CKCON =0x01 or CKCON =0x02? because datasheet is CKCON =0x01
External data memory stretch control. 001: One stretch cycle (default)...
Hi All,
I'm working with Nordic BLE Mesh and trying DFU (OTA) provided in sdk for Mesh.
I used \doc\getting_started\dfu_quick_start.md as the guide to setup and test...
Hello,
I am using nRF52840. I am trying to get hands on DFU. Without any modifications, I am using examples as is.
1) I followed below steps to do DFU hrs_application_s140...
I am looking for some 'getting started' information on configuring the nrf52833 DK for direction finding.
I have read the thread: https://devzone.nordicsemi.com/f/nordic...
Hello,
I have made a custom board based on NRF52840 IC.
The board is using GPIOTE, SPI2 and TWI1, and when put to sleep, consume 665µA. When just initializing the SPI...
Hi,
I would like to read accelerometer value from orientation_detector_calibrate() (in asset_tracker/src/orientation_detector/orientation_detector. c).
But from main.c...
Hi,
I am learning nRF development with 52DK device and SDK v16.0. I noticed that by default the 52DK planned P0.5~8 for UART purpose.
I am wondering if I can disable UART...
Hello ,
I am trying to send 1,000 of MPU-9250 data from NRF5832 peripheral(ble_nus_uart) to NRF52832 central(ble_app_uart_c).
And i have been searched this site and set...
I would like to move existing nRF9160 solution created according to nrfConnect Getting Started Guide to another directory under Windows.
Simply moving the folder doesn't...
