Hello!
I want to develop a Heartrate Monitor Device which uses BLE and ANT+ using the Seeed XIAO nRF52840 Plus Board.
Now that I have the board I found out that ANT doesn...
Hi
I have one nordic nRF54L15 DK using as peripheral, I want to know the power of it. Thus, I use PPK2 to be a 1.8 voltage source and connect VOUT to P6 pin 1 and GND to...
How do I produce a signed file to flash to the network core for firmware update? I am using a child image/parent concept with the \nrf\samples\ipc\ipc_service\ project, When...
Hi,
I’m working with the Wi-Fi station example on the nRF54H20 using SDK v3.0.0, and I’m encountering a critical issue when trying to bring up the nRF7002EK Wi-Fi module...
Hi Nordic team,
I'm trying to configure the GPIOs to operate at 3.3V using the nRF Connect for Desktop's Board Configurator tool (v0.3.10). The tool works as expected...
Hi,
I succeeded in implementing Channel sounding for multiple devices (based on previous samples). But now there is a little difference in how the data gets collected (buffer...
Hello,
we are developing a device which implements BLE hid keyboard. The code is based on the hid keyboard example in the NRF Connect SDK.
The example uses battery service...
Hello,
I am planning on using the WLCSP version of the nRF52840 chip on a PCB design. ( nRF52840 - Bluetooth 5.3 SoC - nordicsemi.com )
Is it possible to program the nRF52840...
I'm attempting to write software onto a newly purchased nRF52840 dongle using nRF Connect for desktop, but I'm unable to do so. My environment is Ubuntu 24.042 LTS. The LED...
Hi,
I am working on a sensor device that requires very accurate timing on the sensing and sensor signal algorithm side. This device needs a low latency and low jitter radio...
Hi, I'm a novice in embedded systems. I have board based on nrf52811 and firmware written for my device but when I received my board from production I could not load firmware...
I run the system_off example without the system actually going off, by removing all the calls to start the system_off worker. Instead of going to off, I let the system enter...
Hi all,
I'm modifying the Matter Light Bulb example from Nordic's nRF Connect SDK to integrate I2S audio output on the nRF5340 DK. The goal is to play a continuous beep...
Hi,
I am working on zigbee demo "light_switch" with NCS2.8 Add-on SDK.I enabled MCUboot according to the steps in the course " Lesson 9 – Bootloaders and DFU/FOTA "
1...
I'm trying to use an ILI9341 display with nRF52840 in Zephyr (v4.1.99). The build fails with multiple errors about missing Devicetree properties when compiling display_ili9xxx...
Hi all,
I've been developing a BLE application on my laptop to communicate with the 52840. I manage to understand how to create and run a BLE connection through the really...
Hello,
I have a legacy project that is using nrf5 sdk v17.0.2. I need to add the BLE DFU functionality to this project based on the nRF52840. Are there any examples on...
Hi,I am using NRF54L15 DK in which I need to transmit audio data over BLE where that data will be used for only plotting in application,I am using sampling rate of 16000 and...
Hi Nordic team,
I'm using the nRF5340 + nRF7002 to securely connect to my backend over HTTPS using Wi-Fi and the native TLS support (mbedTLS).
What works:
I can...
I have been trying to use the Nordic security backend with the MQTT library (TLS transport). However, after I finally got everything to build , I am now getting runtime errors...
When calling the bt_conn_le_create_synced function to create a connection to a peripheral, which is synced to the PAwR train, I get a CONNECTION FAILED TO BE ESTABLISHED ...
