Hello,
We are working on Zephyr sample app Mesh on nRF52840dongle with nRF Mesh application.
After going through the documentation and few other Q&A on the portal, I was...
Hlo
I have to asked that i am working with custom board of nrf5340 and i want to flash and check the rf signal by flashing through the nrf5340 development board and i am...
Hi all,
I'm encountering an issue with the TWIM30 interface on the nRF54L15 (pins P0.03 - SDA, and P0.04 - SCL), using vanilla Zephyr v4.2.0-rc1.
The setup involves external...
Hi,
I purchased a Qorvo QM33120WDK1 UWB development kit that uses a Nordic nrf52840-DK. I have been using this DK for weeks without issues, but the last time I used it...
We are developing a product that will have a wireless and wired option, based on the NRF52840
The strategy is to release the wired option first, followed by the wireless...
Hello,
I'm trying to build the trusted firmware M for the nrf9151.
I did the following steps:
git clone git.trustedfirmware.org/.../trusted-firmware-m
cd trusted...
Hello,
I would like to use the Radio Test Sample from the newest NRF Connect v3.0.2 (v3.0.2\nrf\samples\peripheral\radio_test). However, when I try to build it with "nrf54l15dk...
Looking for a 3rd party supplier with a certified module.
Module pinning makes it possible to program new software into the module.
The question is: If I change the software...
Hello,
I am using nrf51822 with softdevice 110.
I have noticed that there is some power usage between advertisements, that is more than what is being used when no advertising...
We're having difficulty preventing our nRF51822 from resetting when ESD events occur. These events are not directly on the nRF51's I/O pins, and we've tried things like grounding...
Hi,
I am having a BLE peripheral on NRF51822 chip.
I have set to MITM to 0.
I want to communicate with an iOS app which will act as central device.
When i first connect...
Hi,
I'm planning to use the nrF51822 in the end product and the nRF51DK kit has nRF51422 and not the nRF51822. the user guide for the kit says that 51422 supports ANT protocol...
I am doing a bootloader to support updates via ESB. I am using MicroLib. I am not using SoftDevice.
My project mapping:
Bootloader 0x0000-0xBFF
Application Vector Table...
I use Keil uVision 4.74.0.22 to compile nRF51-ble-bcast-mesh-master with nrf51_sdk_v6_1_0_b2ec2e6 and get the rbc_mesh_BLE_Gateway.hex. However, I drag and drop the hex file...
The iOS app we have is identifying the device via the name broadcasted and the service UUID. On production devices, are the Service UUIDs on the same product, the same on...
Fisrt of all, I have searched all the questions but now still can't make bond work.
I've done below work:
1, modify main.c file to add device manger function
2, modify...
Hello,
I am using NUS service as a peripheral with read and write characteristics and tested on master control panel.
Now I am using S120 stack for central device and...
Hi,
I have a PCA10028 which has a 51422, and trying to run ble_app_uart_c example on it. But no success. I don't get any thing on COM and LEDs do not turn on at all. Does...
Good morning,
I am using nRF51 SDK v10.0.0 and I have to synchronize access to a hardware resource shared between two control flows. One flow is an interrupt handler invoked...
I just ported my SDK 9.0 app timer code to SDK 10.0 which requires the use of the new APP_TIMER_DEF() macro. The problem is that is generates warnings in Keil (v5.17) that...
I am using nRF51822. I want to know that how to perform file read, delete and write operations. Is there any API available for this. If file operations are not supported by...
