Hi
I have one nordic nRF54L15 DK using as peripheral, I want to know the power of it. Thus, I use PPK2 to be a 1.8 voltage source and connect VOUT to P6 pin 1 and GND to...
How do I produce a signed file to flash to the network core for firmware update? I am using a child image/parent concept with the \nrf\samples\ipc\ipc_service\ project, When...
Hi,
I’m working with the Wi-Fi station example on the nRF54H20 using SDK v3.0.0, and I’m encountering a critical issue when trying to bring up the nRF7002EK Wi-Fi module...
Hi Nordic team,
I'm trying to configure the GPIOs to operate at 3.3V using the nRF Connect for Desktop's Board Configurator tool (v0.3.10). The tool works as expected...
Hi,
I succeeded in implementing Channel sounding for multiple devices (based on previous samples). But now there is a little difference in how the data gets collected (buffer...
I have a project using BLE as a central on an nRF5340 to connect to several devices. For factory test I am being asked to implement something that can be used in the factory...
I want my peripheral device to act as a beacon while it is in a connected state with a master device. Is it possible to start not-connectable advertising in parallel with...
I am working on a nrf51822 UART bootloader using Keil 5.14 (though I had the same problem with 5.1). If I start with the pack example dfu_dual_bank_serial_s110_pca10028 with...
What happened to NRF_FICR_Type.INFO and FICR_INFO_Type in nrf51.h?
This was in ./components/drivers_nrf/hal/nrf51.h in nRF51_SDK_7.1.0_372d17a
but is missing from ....
Using the nRF51422 with the TWI hardware version. Just playing around to verify signals with the following code which just configures the TWI1 and then repeats continuously...
Hi,
i tried to update the firmware of nRF51-DK but it crashed and now Keil uVision says "Cannot find the JLink version number"
Its also not showing in the nRFgo stu...
I'm developing application using your devices (PCA10001/PCA10000) and S130 SoftDevice. I tried to implement DFU/OTA feature in my app. For this purpose I used DFU sources...
Hi All,
Does anybody has a working setup using SD 7.1.0 with SDK 7.2.0, iOS 8, DFU with a secure connection?
When I use no encryption it works, but when I enable encryption...
So I'm currently trying my hand at some very simple things that one can do with the NRF51-DK.
One of those things involves sending notifications to a client on certain...
Hello,
I'm testing n51822 with low voltage mode, and want to check the BOR condition.
Is there any threshold for brown-out reset, or voltage tolerance? e.g. 1.68V...
Hi.
I have received down the source of the example of experimental_ble_app_uart in my keil.
I use register.(NRF_CLOCK->EVENTS_HFCLKSTARTED = 0;)
but, Hardfault occurs...
Hi there,
I am currently using the nRF51 DK trying to teach myself how to create a working ble application. I am currently going through the application note nAN-36_v1...
Hello!
We are using an BLE NRF51822 chip as a GATT-Server, unfortunately without any possibility to modify its software at the moment. The BLE-setup should be very similar...
I want to run the Direct Test Mode for nRF51422 on my board, I'm trying to use the nRFgo Studio.
When I'm trying to connect to the specific COM port, I get the following...
Custom Board which has NordicSemi nRF51822-QFAA MCU,
a temperature sensor (Si7020-A10), and a white LED. The circuit follows the internal LDO setup.
(Ref. nRF51822_PS...
Hello,
i use Bootloader from SDK 7.2.0. I have some questions about init packet handling:
The bootloader compare the device type, device revision and softdevices...
