Hello,
I'm developing my custom sensor application. It's a matter over thread device. Before final product I'm working on a NRF52840 DK PCA 100056 v3.0.1 and NCS 3.02. It...
Hello!!
When I'm reading carefully about the nRF7002 Power save operations, It's hard to understand about Power save Exit Strategy.
https://docs.nordicsemi.com/bundle...
Hello,
I higly need to run twister unit tests in debug mode with breakpoints, step by step, spies and other debug tools in vscode. I did not find a way to do so.
Is...
Dear devzone, Can our nRF52840 detect 20 nanosecond voltage fluctuations using COMP? For example, if I set a lower threshold of 20mV and an upper threshold of 60mV, and the...
Hi nordic： What is the peak current of NRF9151? The relevant parameter cannot be found in the datasheet, while it is available for NRF9160.
Best Regards
JERMI.JIN
I'm using the nRF52840-DK part number 1490-1072-ND I ordered last week. In both nRF Connect for Desktop and the VS code extension the device wasn't able to detect. Tried two...
Hello, this is probably a very beginner question but I don't know how to configure interrupt for the GPIO headers on the nRF52840 dev kit. I tried to search in this forum...
We have an nRF51822-based product that goes the SYSTEM OFF in certain situations.
We wake up with the DETECT signal from a pin which we set to sensing just before calling...
I want to have it wireless capabilities into the cable, the receiver and transmitter antenna ports with shielded wire connected directly, so there will be a wireless signal...
Hello! I want to broadcast messages between 2/3/4/5/... devices. How Can I broadcasts between devices? Each device must receive messages from others and also broadcasts to...
Hi,
I'm unable to configure the UART so, that it will generate the TXDRDY event. I have an UART that should send periodicaly 4 Byte sequences without hardware handshake...
Hi,
For my research project on novel antennas I need a demonstration prototype, and the nRF51822 Beacon Kit would be ideal for me (due to its small size and battery power...
Hi there,
I was wondering it it is possible to use MATLAB as a central device, using a third party dongle?
The MATLAB Instrumentation Contol Toolbox can be used to control...
Bluetooth v4.2 included an ability for attributes to be greater than 20 bytes of payload data long. Is there anything in the nrf51822 hardware that would prevent this from...
Hi,
Does anyone know the maximum baud rate of the nrf24l01+? I am trying to talk to it through SPI but observe that when I increase SPI speed I read incorrect values. Does...
Recently I was attempting to use the nrf51822 SDK's app_uart module's APP_UART_FLOW_CONTROL_LOW_POWER mode (currently using APP_UART_FLOW_CONTROL_ENABLED ). I noticed that...
Hello,
I would like to send some data i read over I2C. But the I2C and BLE Stack should not run at once, is it possible to check the state of the BLE stack?
The core specification v4.0 vol 3 part C section 3.2.2.3 "Bluetooth Device Name -- Representation" states that the device name can be up to 248 bytes. I've confirmed that...
Dears:
I know there are three modes as below :
(1) internal LDO regulator
(2) 1.8 V low voltage mode
(3) internal DC/DC converter
So, I have some questions as below...
Hi, we are trying to calculate operational current. Does anyone know what the test voltage is in nRF51422_PS v3.1. I assume for typical it's 3.0V and Max is 3.6V?
Also is...
I have a 256k NRF51822 with S110 installed.
I have a small custom bootloader that is located at 0x3f000.
I used nrfgo studio to install the S110 stack, then the bootloader...
