Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
whether one s110 device can connect to multiple s120 devices simultaneously...?
if not what is the special feature mentioned in Bluetooth 4.1 specification..?
is it limitation...
I'm testing ble_app_ancs experimental sample.
It seems working first connection. But after rebooting iOS Device, or Turn Off/On bluetooth function on iOS Device, ANCS does...
I'm developing an UART with SD110. I've updated the SDK to the newest 7.1 and I'm using MDK Pack-Installer.
I found a problem in app_uart.c and retarget.c .
retarget...
I have a nRF24L01+ connecting to an Arduino board using the RF24 library code. It is a print of the registers:
On the nRF51822 I have the following code:
int main...
Hi, I was looking on Digikey and there is a device with the following code: NRF51422-QFAA-R7 V2
Does anyone know what the R7 V2 means? I think R=reel? Thanks
Hello everyone,
I have two nRF51822 (PCA10024) which I want to communicate, one is a peripheral s110 and working properly with a batery service and a custom service, and...
I am new to BT certification so my following question may be incorrectly stated.
We are creating a new OEM BLE module using the nRF51882-CFAC. We intend to sell this module...
Devzone,
I've been working on a central device based on the project 'ble_app_multilink_central' and have encountered an error originating from within the softdevice of...
In Bluetooth 4.1 spec they mentioned scatternet option for BR/EDR topology....not for LE topology...
is that option of connecting to multiple centrals at a time will applicable...
I need a BLE device that can broadcast codes/id to my android mobile app. Also, I need those codes be changed by once in a while by an admin app. Is this possible?
I'm unable to get any output when writing to the UART while using the s110 softdevice. I'm refering to the hardware UART. I'm not using bluetooth for serial.
I'm using...
Hello,
I wrote a firmware for my project, based on the UART over BLE example, so using the softdevice, establishing connections, etc. It works.
I'd now like to use a...
Hi all,
I can program and debug my application just fine when the softdevice is not used (initialized). Problem is, when I do use the softdevice, I end up in Hard Fauld...
Hello,
In our prototype (Embedded System) we want to use nRTF24AP2 with Chip Antenna, as W3006, for example.
Our questions are: where and how needs to be placed the Chip...
Hi there,
I currently have an nRF51 DK set up transmitting six 20 byte packets per 7.5ms, there about, to an nRF51 Dongle set up as a central. When viewing with Master...
