My goal is to control a RC toy drone (4-ch 2.4GHz) from a PC. I've seen some hacks (for example dzlsevilgeniuslair.blogspot.com.br/.../more-toy-quadcopter-hacking.html) using...
Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
Not really a development question. I'm looking for a wearable BLE device to use as a prototype for an academic research project (in a healthcare/hospital setting).
The...
Hi there,
Can anyone help me do secure DFU using bluetooth on PC please? I've tried every possible node.js solution to no avail.
I don't care what programming language...
Hello,
To my understanding, normally, either after a reset or powering up, the program should first run to Reset_Handler, then SystemInit, then __main.
Somehow, my program...
i used RTS service example in nRF5_SDK_13.1.0_7ca7556.
I entered the value in cccd,then i see ATT_ErrorRsp: status=0 oc=0x0012 h=17 err=5.
What's wrong with it and how...
We have tried working with nrF UART android source code from Github, it is not working, we have connectivity issue. it is working fine with the uart application which we have...
Hello, I'm developing firmware for a custom PCB with an nRF52832 chip. I've implemented almost all of the peripheral functionality I need (including TWI, GPIO, GPIOTE, delay...
Hi there,
I've already downloaded ble_mesh_v0.9.1-Alpha SDK and I can use arm-none-eabi-gcc to compile it, one thing I want to know is that how can I switch HWID to 52 in...
Hello,
I'm trying to use ble_app_hrs_rscs_relay_pca10056_s140 on a nRF52840 Preview DK using example from SDK 13.0.0_04a0bfd.
When I copy the precompiled .hex file in...
Hi,
I'm trying to add another element with a simple onoff model to control a second LED on the same server node.
I get APP_ERROR. I try declaring m_server0, m_server1, generic_get0_cb...
Hello,
I want to use at the nRF52832 a temperature sensor TMP108 and an EEPROM via TWI bus which are connected to Pin 5 (SDA) and Pin 6 (SCL). I made a lot of time until...
Hello,
I have a custom board with a Taiyo Yuden chip (it integrates an nRF51822 QFAC chip, 2 crystals and the BLE antenna).
I program it using SWD. I succesfully uploaded...
Hi,
I'm trying to use nRF52832 by external oscillator(ash7k-32.768KGZ-T).
When i use SDK13, i just add clock setting like below.
NRF_CLOCK->LFCLKSRC = (CLOCK_LFCLKSRC_SRC_Xtal...
Hello,
I'm using the SDK 14 and the FDS library.
I'm a bit confused about one thing :
FDS uses Flash Storage to write to flash.
Since SDK14 Flash Storage can work...
