Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
Few weeeks back we have purchased beacons from chinese manufacturer (Radioland China). He had provided me iBeacons. We bought beacons as we are working on some beacon solution...
I am using nRF 52 DK with Softdevice s132 v4.0.2 and app ble_app_uart from sdk 13.0.0
When i try to connect using nRF Toobox running from my Nexus 6p Android phone Segger...
Hi all!
I write for nRF52 but I can't to understand it. There are two cases:
first- I want bound my peripherial with central. And in future I want connect only between...
Hello iam using softdevice 110 and SDK 10.0.0, I have created project using ble_app_uart example code, i have added device manager APIs to manage bonding. Problem is iam GATT...
Basically, it can be divided into two cases
Reading/sampling TX pin of the sensor (since usually nothing is sended back)
Send/Read possibility - in case of range switching...
Hi all, today I was working properly and, in a second my nRF52382 (I use SD s132 V3.0 without bootloader, and SDK 12.2) is "disappeared". I googled and I've found some cases...
I am using nrf51822 with 16k RAM chip, xAA.
I followed the procedures...but I don't know what is wrong with it..
Program secure bootloader with S130 (2.0.0), SDK...
Hello,
I am trying to use the new nRF Connect 2 for Desktop. After installation, the app gets stuck and doesn't show any GUI. Investigating the network shows that the app...
I have been setting up systems to develop nRF52 code for the better part of two years. Maybe I am getting forgetful in my old age, but I can't seem to get it working this...
Hi.
I am looking for appropriate 2.4Ghz Nordic RF chipset.
I have studied 2.4Ghz chipset. but so clearly show about
1:n audio streaming (mono or studio)
exactly what we...
Hi, we are using nrf51822 xxAB based module and would like to understand which SD/SDK combination is best to use in terms of memory usage. We have developed original firmware...
I'm in the process of migrating from SDK11 to SDK13. I have a custom UUID with 3 characteristics (2 notify chars for data and 1 r/w for sending commands), based off HRS and...
Using SDK 12.1.0
I2C with SoftDevice works on PCA10040 Eval Board with nRF52832 but
hangs in the nrf_drv_twi_enable function with TY module EBSGCNZWY which is an
nRF51822...
Attached program has 4 characteristics
UUID_VLEN1 - VLOC_STACK, no rd_auth or wr_auth - value can be read after written
UUID_VLEN2 - VLOC_USER, no rd_auth...
