Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
Hi I would like to ask you for advice on how to solve my problem with Ble and the timer I am trying to add a timer to examples\ble_peripheral\ble_app_uart the timer works...
I want to add some configuration files to nrf52, so can I write data in flash and read when I want.......I have the example code of twi master_twi slave but it engages the...
I have followed the instructions for sniffing ble packets with wireshark. Errors would occur when using 2.2.5 so I switched to the latest development version. See this question...
Hi, I am developer of indoor location tracking solutions for asset tracking applications, actively looking out for new technologies, i would like to understand what are the...
Normally I am using nrf51 for peripheral(sdk 8.0.0 s110) and central(sdk10.0.0 s130) device. But I want to use nrf52 for just central device. I tried nrf52 for central(with...
Hello All
Currently i am using nRF51422-DK (PCA10028) Board .I am planing make mesh network using nRF51 devices.i go through the mesh network introduction document which...
Hi,
I'm trying to set a button as an interrupt source. I wrote this code:
void Init(void){
pwrmng_MainStatus = PWRMNG_STS_STARTUP;
//LED
#ifdef DEBUG_LED
nrf_gpio_cfg_output...
I want to read the status of LFCLK,but I find that ,the value I have readed is awayls zero! my code is follow :
LFCLK_State = ((NRF_CLOCK->LFCLKSTAT) >> 16) & 0x00000001;...
Hi,
I had done secure OTA in nRF51 DK board using SDK 12.2.0 and s130 2.0.1 softdevice. Now, i am trying to same thing with my custom Board RL-51822-A1.
For that first...
I cloned the demo project inside the Keil MDK5, from the following path:
pack installer
device = "nRF51822_xxAC"
examples = "uart_pca10028, UART_Example_Application...
Hi,
I want to use the nRF BLE Sniffer to detect wether a connection (between my fitness tracker and smart phone) is present or not.
I am able to get the advertisement...
hi,
I am struggling to create custom service to send the simple message to the client device where both devices are nRF52832 (Server and client). when I receive the message...
I have 2 of the nRF51 Dev. kits and have been ble to run Blinky, BLE_UART and set up the 2 dev kits so that I can send data from one DK to the other and to an external board...
Hi,
I tried to flash the mbed FOTA bootloader on my nrf51 DK. I copied the bin file to the bootloader device. It said the storage on the device is to small. Now it won...
1- I am looking for Bluetooth Chip to control a DC Motor.
2- This Chip need to be small since it will be fitted on a small narrow PCB (10mm width x 110mm long PCB).
3- Chip...
